F600AT is a low-priced weighing controller that pursues operability and functions. Adoption of the LCD touch panel that allows easy operation without a manual has realized excellent visibility and operability. This is a practical device packed with the functions required for weighing such as direct connectability to PCs and PLCs including RS-232C, DeviceNet and CC-Link, besides the waveform display function.
ANALOG SECTION｜SETTING SECTION｜INPUT/OUTPUT SECTION｜DISPLAY SECTION｜GENERAL SPECIFICATIONS｜ACCESSORIES
| ANALOG SECTION | |
| Excitation voltage | 10V DC ±5％, Output current: within 120mA, Remote sense type (Up to 4 loadcells at 350Ω are operable) |
|---|---|
| Signal input range | -0.2 - 3.0mV/V |
| Zero adjustment range | -0.2 - 3.0mV/V Performed by digital computation |
| Gain adjustment range | Performed by digital computation |
| Accuracy |
Non-linearity: within 0.02% FS±1 digit (at 3mV/V input) Zero drift: within 0.25μV/°CRTI Gain drift: within 25 ppm/°C |
| A/D converter |
Speed: 100 times/sec Resolution: 24 bit (binary) |
| Analog filter | Bessel low-pass filter (-12dB/oct.) selectable from 2, 4, 6, 8 Hz |
| Secondary calibration | Equivalent input calibration method that allows calibration by simply key-inputting the rated value of a sensor without applying an actual load; Min. calibration resolution at secondary calibration (1/1000 at room temperature) |
| SETTING SECTION | |
| Setting method | ･ Set by touch panel operation |
|---|---|
| Memory of set values |
･ Initial values : NOV RAM (nonvolatile RAM) ･ Other values : Lithium-battery-backed-up C-MOS RAM (The memory life is approx. 7 years or more, which varies depending on the operating conditions and storage environment.) Crucial setting values: (calibration, comparison, operational setting, etc.): NOV RAM (Non-volatile RAM) |
| Protection of set values | Setting operation can be prohibited to prevent changes by misoperation. (LOCK1, LOCK2) |
| Setting item |
･ EACH CODE (Comparison mode: HI-LO COMP)…HH, HI, LO, LL ･ EACH CODE (Comparison mode: DIS)…FINAL, SP1, SP2, CPS, AFFC, OVER/HI (selectable depending on setting), UNDER/LO (selectable depending on setting) ･ COMPARISON…Comp Mode Selection, Comp. Inhibit Time, Judging Time, Complete Output Time, AFFC, Cps. Coefficient, Avg. Count of AFFC, Discharge Control Mode, Complete Signal Out, Over/under Comparison, Hi/lo Comparison Selection, Near Zero Comparison, Preset Tare Weight 1, Near Zero, Preset Tare Weight 2 ･ Operation…Digital Filter, Analog Filter, MD (Period), MD (Range), Display Freq., ZT (Period), ZT (Range), Indicate Color, Back Light, Display Select, Hi/lo Output Selection, Lock1, Lock2 ･ Graph…Ggraphic Mode, Trigger Level, X End Point, Y Start Point, Y End Point, Drawing Weight ･ System…Initialization, Self check, Password, Language, Key Valid/invalid, B4 Function Selection ･calibration…Zero Calibration, Span Calibration, Equiv. Input Calibration, Balance Weight, Min. Scale Div., Net Over, Gross Over, Unit Display, Decimal Place, DZ Regulation Value ･ Sequence Mode…Sequence Mode, Adjust Feeding, At Start NZ Conf., At Start WV Conf., Adjust Feeding Time, AZ Times, Judging Times |
| INPUT/OUTPUT SECTION | |
| External output signal | Able to select HI/LO limit comparison mode or final discharge mode depending on setting, Transistor’s open collector output (Emitter = COM terminal); Output is LO when transistor is ON. |
|---|---|
| At HI/LO limit comparison Mode | Hi-hi limit, high limit, go, low limit, lo-lo limit, near zero, weight error, stable |
| At Final Discharge mode | SP1, SP2, SP3, COMP, Over/High limit, High/Low limit, near zero, weight alarm or sequence error, stable |
| External input signal |
ON when shorted to COM terminal by contact (relay, switch) or non-contact (transistor, open collector) Digital zero, tare subtraction, tare subtraction reset, hold or judgment, feeding or discharging selection, display select, code select/key LOCK, start, stop |
| DISPLAY SECTION | |
| Display unit | TFT color LCD module (display screen: 71 (W) x 53 (H) mm, 320 x 240 dot |
|---|---|
| Display value | 5 digits, Minus sign on most significant digit. |
| Min. scale division | 1 to 100 selectable |
| Decimal point | Selectable decimal place at 88.8.8.8 |
| Display frequency | Selectable from 3, 6, 13, 25 times/sec (system speed 100 times/sec) |
| Over scale | A/D converter input over: “LOAD”; A/D converter input minus over: “LOAD”; Net weight exceeds preset net weight over: “NET WEIGHT OVER”; Gross weight exceeds preset gross weight over: “GROSS WEIGHT OVER” |
| Unit display | Selectable from t, kg, g, N. lb, none |
| Status display |
NET: Lights when the net is displayed. GROSS: Lights when the gross is displayed. HOLD: Lights in holding. STAB: Lights at stable-time. ZT: Lights in zero tracking. ZALM: Lights when the zero alarm signal is ON. NZ: Lights in near zero ※1 HH: Lights when the hi-hi limit signal is ON. ※1※3 HI: Lights when the high limit signal is ON. ※1 GO: Lights when the preset low limit value <= weight value <= preset high limit value. ※1※3 LO: Lights when low limit signal is ON. ※1 LL: Lights when the lo-lo limit signal is ON. ※2※3 SP1: Lights when the final weight-SP1 >= net weight. ※2※3 SP2: Lights when the final weight-before final >= net weight. ※2※3 SP3: Lights when the final weight-FF >= net weight ※2※3 COMP: Lights when the underweight signal is ON. ※2 OVER: Lights when the overweight signal is ON. ※2 UNDER: Lights when the underweight signal is ON.
※1 Displayed only in the HI/LO limit comparison mode. |
| GENERAL SPECIFICATIONS | |
| Power supply voltage |
100 - 240V AC (+10% - 15%) (Free power supply 50/60 Hz) 24V DC (±15%) (Please specify when ordering) |
|---|---|
| Power consumption | 18W max. |
| Operating conditions |
Temperature: Working temperature range -10 to +40°C; Storage temperature range -20 to +60°C Humidity: 80% RH or less (non-condensing) |
| External dimensions | 96 (W) x 96 (H) x 138 (D) [mm] (protruding parts not included) |
| ACCESSORIES | |
| AC input cord (3m) | 1 |
|---|---|
| Mini-driver for terminal block connection (when DAC option is installed) | 1 |
| Jumper cable | 2 |
| FCN series I/O connector (with cover) | 1 |
| BCD output connector (when BCO option is installed) | 1 |
| DeviceNet connector (when DeviceNet option is installed) | 1 |
| CC-Link connector (when CC-Link option is installed) | 1 |
| Operation Manual | 1 |
| Model | Description |
| BCO | BCD parallel data output interface |
|---|---|
| DAV | D/A converter voltage output |
| DAI | D/A converter current output |
| CCL | CC-Link interface |
| ODN | DeviceNet interface |
| Model | Description |
| CA372-I/O | Cable with FCN connector at one-end 3m |
|---|---|
| CA600-BCDCNV | FCN connector 32p-57・36p cabtyre cable 0.3m |
| CA81-232X | miniDIN-D-Sub9p cross cable 1.5m |
| CAAC2P-B3 | AC Supply cord 3m |
| CAAC3P-CEE7/7-B2 | AC Supply cord (Voltage resistance:250V)2m |
| CN50 | FCN series I/O connector (with cover) |
| CN51 | BCD output connector |
| CN55 | FCN series I/O connector (with diagonal cover) |
| CN60 | Circular DIN 8p connector for RS-232C |
| CN71 | CC-Link connector |
| CN80 | Analog I/O connector terminal |
| CND01 | DeviceNet connector |
| GMP96×96 | Rubber packing |
Malaysia
