LEDVANCE OPTOTRONIC FIT CS G3 - OT FIT 40/220…240/1A0 CS
OT FIT 40/220…240/1A0 CS
Product family features
Lifetime: up to 50,000 h (temperature at max. tc)
Cable clamp kit for independent mounting
Product family benefits
Higher quality of light thanks to low output ripple current
High flexibility due to four different output currents
Small housing for flexible luminaire designs
High efficiency
Areas of application
Suitable for downlights, spotlights and LED panels
Suitable for luminaires of protection classes I and II
Electrical data
Nominal input voltage : 220…240 V
Mains frequency : 50/60 Hz
Input voltage AC : 198…264 V
Total harmonic distortion : < 10 % 1)
Power factor λ : 0.98
Efficiency in full-load : 90 % 2)
Device power loss : 4.9 W 3)
Protective conductor current : <0.7 mA
Inrush current : ≤ 35 A 4)
Max. ECG no. on circuit breaker 10 A (B) : 11
Max. ECG no. on circuit breaker 10 A (C) : 19
Max. ECG no. on circuit breaker 16 A (B) : 19
Max. ECG no. on circuit breaker 16 A (C) : 31
Max. ECG no. on circuit breaker 25 A (B) : 29
Surge capability (L/N-Ground) : 2 kV
Surge capability (L-N) : 1 kV
Nominal output voltage : 25…42 V / 30...42V 5)
U-OUT (working voltage) : 60 V
Nominal output current : 800 / 900 / 950 / 1050 mA
Output current tolerance : ±7.5 %
Default output current : 1050 mA
Output ripple current (100 Hz) : < 5 %
Output PSTLM : ≤1
Output SVM : ≤0.4
Nominal output power : 20…44.1 W
Maximum output power : 44.1 W
Galvanic isolation : SELV
Galvanic isolation primary/secondary : SELV
Current set : DipSwitch
At full load, 230 V, 50 Hz / see graphs
at 230 V, 50 Hz
At 230 V, Input power 49 W max.
twidth = 200 µs (measured at 50 % Ipeak)
30 - 42V @ 1050 mA
Dimensions & weight
Mounting hole spacing, length : 88.0 mm
Mounting hole spacing, width : 34.0 mm
Product weight : 110.00 g
Cable cross-section, input side : 0.5…1.5 mm²
Cable cross-section, output side : 0.5…1.5 mm²
Wire preparation length, input side : 7…8 mm
Wire preparation length, output side : 7…8 mm
Length : 97.0 mm
Width : 43.0 mm
Height : 29.5 mm
Colors & materials
Casing material : Plastic
Temperatures & operating conditions
Ambient temperature range : -20…+50 °C
Maximum temperature at tc test point : 80 °C
Max.housing temperature in case of fault : 110 °C
Temperature range at storage : -20…80 °C
Permitted rel. humidity during operation : 5…85 % 1)
Non-condensing
Lifespan
ECG lifetime : 50000 h 1)
At maximum Tc = 80°C / 10% failure rate
Additional product data
Predecessor EAN : 4052899435650
Capabilities
Dimmable : No
Overheating protection : Automatic reversible
Overload protection : Automatic reversible
Short-circuit protection : Automatic reversible
No-load proof : Yes
Intended for no-load operation : No
Max. cable length to lamp/LED module : 2.0 m 1)
Suitable for fixtures with prot. class : I / II
Type of connection, input side : Push terminal
Type of connection, output side : Push terminal
Suitable for through-wiring : No
Control interface : -
Detection angle (Light sensor) : -
Detection angle (PIR) : -
Number of channels : 1
Output wires must be routed as close as possible to each other
Programming
Programming device : DIPswitch
Certificates & standards
Approval marks – approval : CCC / CE / RCM / ENEC 05
Standards : Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to / IEC 62384/Acc. to CISPR 15/Acc. to IEC 61000-3- / 2/Acc. to IEC 61000-3-3/Acc. to IEC 61547
E S L Lighting (M) Sdn BhdLED Lighting Supplier Selangor, Lighting Shop Seri Kembangan, Kuala Lumpur (KL), Decorative Lighting Supplies Malaysia ~ E S L Lighting (M) Sdn Bhd
.png)
Malaysia
