TF3: 马来西亚的首选 HMI Audio Visual Sdn Bhd

详情

Product Details:

General specifications

Sampling frequency rate	Internal	48 kHz
Signal delay		Less than 2.6 ms, INPUT to OMNI OUT, Fs=48 kHz
Fader		100 mm motorized, Resolution = 10-bit, +10 dB to –138 dB, –∞ dB all faders
Total harmonic distortion		Less than 0.05% 20 Hz–20 kHz @+4 dBu into 600 , INPUT to OMNI OUT, Input Gain=Min. (Measured with a –18 dB/octave filter@80 kHz)
Frequency response		+0.5, –1.5 dB 20 Hz–20 kHz, refer to +4 dBu output @1kHz, INPUT to OMNI OUT
Dynamic range		110 dB typ., DA Converter, 107 dB typ., INPUT to OMNI OUT, Input Gain=Min.
Hum & noise level	Equivalent input noise	–128 dBu typ., Input Gain=Max. (Measured with an A-Weight filter)
	Residual output noise	–85 dBu, ST master off (Measured with an A-Weight filter)
Crosstalk		–100 dB (Measured with a –30 dB/octave filter@22 kHz), adjacent INPUT/OMNI OUT channels, Input Gain=Min.
Power requirements		100–240 V 50/60 Hz
Power consumption		110 W
Dimensions	W	716 mm (28.2in)
	H	225 mm (8.9in)
	D	599 mm (23.6in)
Net weight		17.0 kg (37.5lb)
Accessories		Quick Guide, Power Cord, CUBASE AI download information
Options		Expansion Card, Foot Switch (FC5)
Others		Operating temperature range: 0–40 °C, Storage temperature range: -20–60 °C

Analog input characteristics

Input Terminals	GAIN	Load Impedance	For Use With Nominal	Input Level			Connector	balanced / Unbalanced
				Sensitivity*1	Nominal	Max. before clip
INPUT1-24	+66dB	7.5KΩ	50-600Ω‑ Mics or 600‑Ω Lines	-82dBu (61.6V)	-62dBu (0.616mV)	-42dBu (6.16mV)	Combo Jack (XLR-3-31 type 2 or TRS phone 3)	Balanced
	-6dB			-10dBu (245mV)	+10dBu (2.45V)	+30dBu (24.5V)
ST IN 1,2	—	10kΩ‑	600‑Ω Lines	-30dBV (31.6V)	-10dBV (316mV)	+10dBV (3.16V)	RCA Pin Jack	Unbalanced

*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.)
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND
*In these specifications, 0dBu = 0.775Vrms.
*+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.

Analog output characteristics

Output Terminals	Source Impedance	For Use With Nominal	GAIN SW	Output Level		Connector	balanced / Unbalanced
Output Terminals	Source Impedance	For Use With Nominal	GAIN SW	Nominal	Max. before clip	Connector	balanced / Unbalanced
OMNI OUT 1-16	75‑Ω	600Ω‑ Lines	“+24dBu” position (default)	+4dBu (1.23 V)	+24dBu (12.3 V)	XLR-3-32 type *1	Balanced
PHONES *3	100‑Ω	40Ω‑ Phones	—	3mW	75mW	Stereo Phone Jack (TRS) *2	Unbalanced

*1.1: GND,2: HOT, 3: COLD
*2 Tip: LEFT, Ring: RIGHT, Sleeve: GND
*3 The position of the level control is lowered by 16dB from the maximum.
*In these specifications, 0dBu = 0.775Vrms.
*All output DA converters are 24bit, 128times oversampling.

Indent Order

更多 HMI Audio Visual Sdn Bhd 相关资料