Cedar Digital Torque Driver (DID Series)

Cedar Digital Torque Driver (DID Series)

Category: Torque Equipment Available
For more information, visit our official website at mspmetrology.com.my

Description

Cedar Digital Torque Driver DID Series provide a wide range of torque measurement with a very high accuracy by MSP Metrology (M) Sdn Bhd from Cedar Japan.

Feature

- The torque screwdriver is Ergonomic and light weight, yet ruggedly constructed
- Available in: lb-in, kg-cm and N-m (mN-m)
- Peak, Real Time and Peak Down measuring mode (selectable)
- 800 data memory
- Programmable High and Low set points with both audible beep and Green/Red LED indicator for uniform torque tightening or GO/NO GO testing

- Programmable screw tightening counter
- Programmable Auto Zero function resets unit to zero for easy operation
- Both CW and CCW operation
- ASCII format output (USB)
- Runs on internal NI-MH batteries (for 12 hours) Auto shut-off after 10 min, of non-use
- AC charger and carrying case included

Yes-No Decision Conditions, Etc.. Can Save Five Channels

- A channel is only changed even if bolting conditions change.
- It is not necessary to reset up a maximum value and a minimum value one by one like former.

Full Specifications

Specification DID-05 DID-4
Measuring Range

2.0 ~ 500 mN-m

0.020 ~ 5 kgf-cm

0.020 ~ 4.5 lbf-in

0.020 ~ 4 N-m

0.20 ~ 40 kgf-cm

0.20 ~ 35 lbf-in

Accuracy ±0.5% (499 or less digit ±3 digit)
Display The 4 figures digital display of LCD
The measurement direction CW-CCW (right and left)
Measuring 
mode
P-P Peak Peak load value hold
T-R Track Indication of real time torque value.
P-D Peak down Holding Load Value at the moment to change from upward to downward
C Real-time output Load torque value is outputted every about 1/160 second
Decision 
function
Setting of torque value Programmable High and Low setpoints with both audible beep and Green/Red LED indicator for uniform torque tightening or GO/NO GO testing
The Maximum, the minimum, and the average value The data number, the maximum, the minimum value, and the average value of memory data are displayed.
Automatic Clearance Automatically clear the displayed value after certain time (0.5 – 3.0 sec, selectable at each 0.5 sec). Setting 0.0 sec for manual Zero clearance
A setup of the number of counts One to 99 count (count in a direction with a bundle)
Data spec Data transfer

ASCII format (Baud rate: 19200)

When outputting data,the cable(USB mini B) is needed.

Data memory 800 data
Power supply Ni-MH chargeable battery 1.2V × 4 cells 800mAh
Auto power save 10 minutes no use, automatically switch off.
Charging time   From empty – less than 5 hours
  Continuous working time 12 hours
Bit/Socket part φ4 HEX6.35
  Weight About 180g About 400g
Attachment

Bit (+) #1 

For one-way ×1 For fixation×1

Bit (+) #1 #2
Bit holder
One way Bit holder
    Accessories
 (one piece each)
AC/DC adaptor
An inspection report, a proofreading certificate, a traceability system figure

More detail about MSP Metrology (M) Sdn Bhd
MSP Metrology (M) Sdn Bhd
MSP Metrology (M) Sdn Bhd Video Measuring Machine Johor Bahru (JB), Digital Microscope Supplier Malaysia, Selangor, Hardness Tester Supply Kuala Lumpur (KL), Penang, Singapore ~ MSP Metrology (M) Sdn Bhd
Contact Us flagMalaysia