The best solution for OK/NOK judgment of press fitting and caulking application !! High responsiveness of 5kHz to fully utilize the performance of Super Cell !!
A fluctuation of force is shown as a waveform.
FS2000 is a digital indicator integrated with a strain gauge sensor that can display physical quantities such as pressure, load and torque in waveforms. It is able to visually capture in waveforms the fluctuations in physical quantities which are difficult to capture by only numerical values. With a 25000 times per second for high-speed processing, it is also ideal for narrow value fluctuations and comes equipped with a HI/LO limit comparison function, various hold functions and judgment function. FS2000 can be used in a wide-range of applications such as in control systems used in production control, automatic devices or testers.
Two-dimensional OK/NOK judgement can be performed with a load cell and displacement sensor.
■ Waveform comparison
This function compares the actual measurement waveform against the setup High/Low limit waveforms and will give out an NOK judgment when any of the point exceeded the preset High/Low limit waveforms.
■ Multi-point judgment
OK/NOK judgment can be performed on multi points in one process. (e.g. The start point and end point of press fitting can be judged respectively.)(Max. 5 points)
4.3 inch wide display provides excellent visibility.
Main display configuration can be selected to keep it as simple as possible by eliminating unnecessary information.
Trend of the zero-point shift and hold values can be monitored to find any irregularities for preventing breakdown of machines.
In addition, the master settings can be registered so that operator can compare with the current settings to see if there are any differences.
Master and current set values are listed up for checking the changed setting items easily.
Set values can be edited directly on the list without going into each setting menu.
* Except for waveform comparison settings.
Measured data and set values can be saved in the SD card. Data can be converted to CSV format easily for editing with Microsoft Excel.
Sensor input（Standard）｜Sensor input（Multisensor input：MLT）｜Analog voltage output｜Display section｜COMP. & JUDGE. function｜Preventive maintenance support｜External signal｜Interface｜General performance｜Attachments
| Sensor input | |
| Sensor input for load (Fixed as strain gauge input)(6-wire) | |
| Excitation voltage |
DC 2.5, 5, 10V±10% (depending on settings) Output current: Within 30mA |
|---|---|
| Signal input range | -2.0mV/V to +2.0mV/V |
| Accuracy |
Non-linearity: Within 0.02%/FS ±1 digit (at 2.0mV/V input) Zero drift: Within 0.1μV/℃ RTI Gain drift: Within 15ppm/℃ |
| Low-pass filter |
Selectable from 10 to 10kHz（at A/D converter speed 25000 times/sec） Selectable from 2 to 2kHz（at A/D converter speed 5000 times/sec） |
| A/D converter |
Speed: Selectable from 25000 times/sec., 5000 times/sec. Resolution: 24bit (binary) |
|
Sensor input for displacement Pulse input(Line driver) |
|
| Max. input frequency | 1MHz |
| Internal count range | Approx. 1,000,000 |
| Adaptable rotary encoder |
Output: Incremental type 2-phase output (A/B signal output) Also capable of single-phase output (A-phase input used. All pulses are counted as in the plus direction.) Output stage circuit specification: Line driver (Based on RS-422) |
| Sensor input（Multisensor input：MLT or MLT2） | |
| Sensor input for load (Fixed as strain gauge input)(6-wire) | |
| Excitation voltage |
DC 2.5, 5, 10V±10% (depending on settings) Output current: Within 30mA |
|---|---|
| Signal input range | -2.0mV/V to +2.0mV/V |
| Accuracy |
Non-linearity: Within 0.02%/FS ±1 digit (at 2.0mV/V input) Zero drift: Within 0.1μV/℃ RTI Gain drift: Within 15ppm/℃ |
| Low-pass filter |
Selectable from 10 to 10kHz（at A/D converter speed 25000 times/sec） Selectable from 2 to 2kHz（at A/D converter speed 5000 times/sec） |
| A/D converter |
Speed: Selectable from 25000 times/sec., 5000 times/sec. Resolution: 24bit (binary) |
|
Sensor input for displacement Pulse input (Open collector)[MLT] |
|
| Max. input frequency | 1MHz |
| Internal count range | Approx. 1,000,000 |
| Adaptable rotary encoder |
Output: Incremental type 2-phase output (A/B signal output) Also capable of single-phase output (A-phase input used. All pulses are counted as in the plus direction.) Output stage circuit specification: Open collector (built in pull-up resistor) |
|
Sensor input for displacement Pulse input(Line driver)[MLT2] |
|
| Max. input frequency | 1MHz |
| Internal count range | Approx. 1,000,000 |
| Adaptable rotary encoder |
Output: Incremental type 2-phase output (A/B signal output) Also capable of single-phase output (A-phase input used. All pulses are counted as in the plus direction.) Output stage circuit specification: Line driver (Based on RS-422) |
| Voltage input | |
| Signal input range | －10 to ＋10V |
| Input impedance | App. 1MΩ |
| Accuracy |
Non-linearity:Within 0.02%/FS ±1 digit (at 10V input) Zero drift:Within 0.2mV/℃ RTI Gain drift:Within 0.01%/℃ |
| Low-pass filter |
Selectable from 10 to 10kHz（at A/D converter speed 25000 times/sec） Selectable from 2 to 2kHz（at A/D converter speed 5000 times/sec） |
| A/D converter |
Speed:Selectable from 25000 times/sec, 5000 times/sec Resolution:24bit Effective Resolution: Approx. 1/20000 against 10V |
| Analog voltage output |
Output level: Approx. 2V per 1.0mV/V input Load resistance: 2kΩ or more |
|---|
| Display section | |
| Display |
4.3 inch TFT color LCD module Display area: 95.0(W)×53.9(H) mm Dot configuration: 480×272 dot |
|---|---|
| Display frequency | Fixed at 3 times/sec. |
| COMP. & JUDGE. function | |
|
Multi point comparison mode 16ch (setting values can be stored) |
Capable of judging up to 5 hold points at the same time. Sample, Peak, Bottom, P-P, Relative Maximum, Relative Minimum, Inflection Point, Average, End |
|---|---|
|
Waveform comparison mode 16ch (setting values can be stored) |
Compares the actually measured waveform against the preset Hi/Lo waveforms. The overall measured waveform will be compared against the preset Hi/Lo and if any of its points exceeds the preset waveform, then the measured waveform will be NOK. |
| Preventive maintenance support | |
| Trend display | Showing the trend of measurement data to help finding irregularities at early stage. |
|---|---|
| Statistics |
Using the latest 10000 measured data. Displaying number of measurement, OK, NOK |
| Screen capture | Saves screen capture data as bmp data. |
| Work name edit | Work name can be edited and displayed for each Work No.. |
| Setting list display | Changed setting items comparing to master set values are highlighted. |
| User management | Login ID and Password |
| External signal | |
| Output signal |
16 points Hold judgment (load, displacement)/ Load overload/ Measurement complete/ Waveform comparison judgment/ Load & displacement OK/ CPU OK/ SD card OK/ Timing output 1,2 Output Type: Sink type/source type selectable. (Source Type is option: [ISC]) Output transistor ON at signal ON. To connect an input unit like a PLC, connect plus common for sink type, and minus common for source type. Rated voltage: 30V Rated current: 30mA |
|---|---|
| Input signal |
16 points Load digital zero/ Displacement adjustment/ Measurement start/ Measurement end/ HOLD1 to 5/ Reset/ Forcibly light up the backlight/ Touch panel lock/ Work change Input type: Plus common/Minus common selectable. (Minus common is option: [ISC]) To connect a transistor, connect NPN output type (sink type) for plus common and PNP output type (source type) for minus common. |
|
Interface Only one option can be installed. |
|
| USB | USB interface |
|---|---|
| ODN | DeviceNet interface (option) |
| CCL | CC-Link interface (option) |
| EIP | EtherNet/IP interface (option) |
| General performance | |
| Power supply voltage | DC24V (±15%) |
|---|---|
| Power consumption | 6W typ |
| Operation condition |
Operation temperature: -10℃ to +40℃/ Storage temperature: -20℃ to +60℃ Humidity: 85% RH or less (non-condensing) |
| Dimensions | 132(W)×98(H)×110(D) mm (Projections excluded) |
| Weight | Approx. 1.0kg |
| Attachments | |
| I/O connector (with cover) | 1 |
|---|---|
| Analog connector | 1 |
| Operating tool | 1 |
| SD card | 1 |
| Operation manual | 1 |
| DeviceNet connector (when DeviceNet option is selected) | 1 |
| CC-Link connector (when CC-Link option is selected) | 1 |
| Model | |
| ISC | I/O source board |
|---|---|
| MLT | Multisensor input |
| MLT2 | Multisensor input |
| ODN | DeviceNet interface |
| CCL | CC-Link interface |
| EIP | EtherNet/IP interface |
| Model | |
| CN71 | CC-Link connector |
|---|---|
| CN72 | Double row connector for CC-Link |
| CN77 | Analog connector |
| CND01 | DeviceNet connector |
| SD1G | 1 GByte SD card |
| SD2G | 2 GByte SD card |
| SD16G | 16 GByte SD card |
| SD32G | 32 GByte SD card |
| CA81-USB | USB cable (A-miniB type) 1.8m |
| TSU03 | DC lighting surge unit |
|
Product catalogue(PDF)
|
FS2000_catalogue(654 KB) | |
|---|---|---|
Malaysia
