PELCO Precision Low Speed Saw: Top Choice in Johor Bahru (JB), Malaysia, Selangor, Kuala Lumpur (KL), Penang Atomic Solutions Sdn Bhd

Description

Multipurpose, low-damage cutting for all specimen types

Description:

The PELCO® Precision Low Speed Saw is a compact, multipurpose, precision saw designed to cut a wide variety of materials with minimal subsurface damage. Its low speed makes it possible to cut fragile materials that would otherwise fracture as well as soft materials that would load the diamond wheel on a higher speed saw. A variety of sample holders are available, providing a means for mounting any shape of sample, while multi-axis goniometer adaptability simplifies cutting oriented crystals.

Features:

The belt drive system eliminates gear breakage which is common with less reliable fiber gear driven designs.
The coolant reservoir is lowered and easily removed by opening an access door located on the front panel.
Both coarse and fine sample position adjustments allow rapid and accurate sample positioning.
The polyethylene coolant reservoir enables the use of both water soluble and oil based coolants.
Automatic termination of the cutting process is controlled by an electromechanical downstop which minimizes supervision.
The cutting arm pivots on a set of precision bearings rather than on the micrometer shaft which ensures accurate and repeatable sample positioning.
The PELCO^® Precision Low Speed Saw utilizes a high torque 1/15 HP DC motor to provide sufficient power for difficult materials.
Automatic overload protection shuts down the motor if the blade binds while cutting.
A wide variety of sample holders allow mounting of virtually any shape of sample.

Specifications:

Dimensions: Length 33cm (13'') x Width 33cm (13'') x Height 23cm (9'')
Universal Power: 100-240 VAC, 50/60 Hz
Speed: 50-300 RPM
Blade Sizes: 3'' or 4'', with a 0.5'' arbor
Maximum Cut Depth: 1.25''
ETL and CE certified

Accessories

Single-Axis Goniometer
The Single-Axis Goniometer has a graduated scale with a 0.2° vernier and can be rotated 360°. This rotational capability makes it ideal for precisely slicing single crystals. The sample is mounted to a block using a low melting point wax and the block is subsequently clamped into the PELCO^® Precision Low Speed Saw. Wax mounting of the sample ensures that the cut piece will remain attached to the holder and will not be damaged due to falling after being cut.

2-Axis Goniometer

2-Axis Goniometer
The 2-Axis Goniometer is used for orienting and cutting single crystals. With the sample mounted to the goniometer, the vertical axis can be rotated +/- 50° from the 0.2° vernier on the arm.

Double Clamp Sample Holder

Double Clamp Sample Holder
The Double Clamp Sample Holder is designed to clamp both ends of a round or rectangular rod while cutting between the two clamped positions.The Double Clamp Sample Holder can also be used as a single clamp holder to hold encapsulated metallurgical samples up to 1.25'' in diameter.

Petrographic Vacuum Sample Holder

Petrographic Vacuum Sample Holder
The Petrographic Vacuum Sample Holder is designed to use a vacuum to hold a 2.5 x 5.0cm (1 x 2'') glass slide, onto which petrographic or other samples are mounted, while making saw cuts parallel to the glass slide. The glass slide is held against a stainless steel support plate with vacuum and is placed firmly against three locating pins to maintain its position.

Vise Sample Holder

Vise Sample Holder
The Vise Sample Holder is designed to hold flat, round and irregularly shaped samples without the need for mounting wax. The entire vise can rotate 360° in the horizontal plane. An extended v-notch jaw enables the mounting of cylindrical samples up to 1.25'' in diameter including encapsulated metallurgical samples.

Bone Chuck

Freeform Sample Holder, ''Bone Chuck''
The ''Bone Chuck'' allows you to hold the sample utilizing a series of ten independently adjustable mounting screws. These mounting screws make it possible to hold irregularly shaped specimens and rotate them 360° in a horizontal plane. The Bone Chuck attaches to the standard work arm in place of the standard sample holders.

More detail about Atomic Solutions Sdn Bhd