Torque monitor for UTMⅡ/UTMV
* Torque monitor specialized for UTMⅡ/UTMV
* Torque, rotation speed and power are displayed simultaneously
* Hold function
（Sample, Peak, Valley, P-P, Average）
* Upper/lower comparators function
（ALM HI, HI, OK, LO, ALM LO）
* Data storage function
* Easy connection to UTMⅡ/UTMV with one cable
* The unit supplies electric power to UTMⅡ/UTMV.
* Variation of torque, rpm, and power can be monitored and saved on PC. (with USB interface option only)
Sensor input for torque｜Drive power supply for UTMⅡ/UTMV｜Pulse input for rotation speed｜Display section｜Setting section｜External input/output section｜General performance｜Attachment
| Sensor input for torque (voltage input) | |
| Input resistance | 1MΩ |
|---|---|
| Signal input range | ±5V |
| Accuracy |
Non-linearity:Within 0.02%/FS±1digit Zero drift:Within 0.2mV/℃ RTI Gain drift:Within 0.01%/℃ |
| A/D converter |
･ Speed…300 times/sec. ･ Resolution…24bit(binary) Approx. 1/30000 with respect to 5V |
| Analog filter | Low-pass filter（-6dB/oct） Selectable from 3, 30, 300, and 1kHz. |
| Voltage output | Input voltage cuff (For test point) |
| Drive power supply for UTMⅡ/UTMV | |
| Power supply voltag | DC24V *One UTMⅡ/UTMV at the maximum |
|---|---|
| Pulse input for rotation speed (open collector input) | |
| Maximum input frequency | In accordance with the output frequency of the UTMⅡ/UTMV series |
|---|---|
| Minimum input frequency |
Select from 15, 10, 5, 3, or 2 rpm (when pulse rate is 4 ppr) 60, 40, 20, 12, 8 rpm (when pulse rate is 1 ppr) |
| Minimum detection pulse width | 50μs |
| Circuit configuration |
No-voltage contact input (minus common) Open collector connectable（Ic＝Approx. 10mA） |
| Display section | |
| Display |
Main display：Character height 15mm Numerical display by 7-segment green LED（5-digit+sign） Sub display ：Character height 8mm Numerical display by 7-segment green LED（5-digit） |
|---|---|
| Indicated value |
Main display：5-digit －99999～＋99999 Signs: Minus sign on most significant digit Sub display ：5-digit －19999～＋99999 Signs: Minus sign on most significant digit |
| Decimal point | 0, 0.0, 0.00, 0.000（Only a torque and a power. Rotation speed is nothing） |
| Display frequency | Selectable from 3, 6, 13, and 25 times/sec. |
| Status display | HI／LO／HOLD |
| Setting section | |
|
Setting item |
HI/LO limit： HI limit ／LO limit／Alarm HI limit／Alarm LO limit Comparison/hold： Comparison function select／Near zero／Hysteresis／Hold function select／Detection time／Average sample number／Hold start level Operation 1： Motion detect (time)／Motion detect (range)／Zero tracking (time)／Zero tracking (range)／SI/F function select／Display frequency／Display ON/OFF Operation 2： Digital filter (torque)／Analog filter (torque)／Dead band／Digital filter (rotation speed) Calibration： Calibration function select 1(torque)／Zero calibration／Equivalent input calibration／Actual load calibration／Digital offset／Digital Zero limit／Calibration function select 2 (rotation speed/ power) Protect/Initializ： Setting protect／Key protect／Initialize／Password／Record data clear |
|---|---|
| Hold |
Sample, Peak, Valley, P-P, Average Hold section setting (All section・External signal・External signal + Time・Level + Time) |
| External input/output section | |
|
External input （4） |
Hold control／Hold reset／Digital Zero／Record data clear Dry contact input circuit (minus common type), Ic＝10mA or less |
|---|---|
|
External output （7） |
HI/LO limit comparison（alarm HI・HI・OK・LO・alarm LO） ／Hold complete／RUN Open collector output circuit (sink type), Vceo＝30V（max） Ic＝30mA（max） |
| Interface |
*Only one option can be installed. |
| General performance | |
| Power supply voltage | AC100V～240V(+10%-15%)(free power source) 50/60Hz |
|---|---|
| Power consumption | 14W max |
| Operating conditions |
Operation:-10～+40℃ Storage-40～+80℃ Humidity:85%RH or less(non-condensing) |
| Dimension | 96(W)×96(H)×138(D) mm(Projections excluded) |
| Panel cutout size | 92×92(+1-0)mm |
| Weight | Approx. 1.0kg |
| Attachment | |
|
External input/output connector ×1 AC input cord 3m（with solderless terminal）* ×1 Cable for UTMⅡ/UTMV connection 2m ×1 Unit seal ×1 Connector for BCD output（with BCD output option） ×1 Operating tool（with D/A converter(3ch) option） ×1 Mini screwdriver（with D/A converter option） ×1 Operation manual ×1 *The attached AC input cord is intended for 100V AC power in Japan. |
|
| Model | Description |
| BCO | BCD parallel data output interface |
|---|---|
| 232 | RS-232C communication interface |
| D3V | D/A converter voltage output(3ch) |
| DAV | D/A converter voltage output |
| DAI | D/A converter current output |
| USB | USB interface |
| Model | Description |
| CA372-I/O | Cable with FCN connector at one-end 3m |
|---|---|
| CAAC2P-B3 | AC Supply cord 3m |
| CAAC3P-CEE7/7-B2 | AC Supply cord (Voltage resistance:250V)2m |
| CN34 | D-Sub9p connector for RS-232C |
| CN50 | FCN series I/O connector (with cover) |
| CN51 | BCD output connector |
| CN55 | FCN series I/O connector (with diagonal cover) |
| CN73 | D/A converter(3ch) connector |
| CN90 | Waterproof plastic connector for UTMⅡ/UTMV connection |
| DTC2-PSL | Case for TM301 |
