* D/A converter corresponds to voltage output and current output.
* BCD output corresponds to sink type and source type.
The peak or a sample point of digitized measurement data is captured.
It is ideal for applications where the stability of reading is required.
Analogue signal from a sensor can be converted to digital signal at the rate of 3000 times/sec.*.
* A/D conversion rate can be switched to 30 or 300 times/sec..
Then the effect of filter is enhanced, which, in turn, enables stable measurements.
Remove vibration and noise/external interference on input signal for “fast” and “accurate” reading.
Both analogue and digital filters (low-pass and moving average filter) can be used simultaneously.
Depending on requirements for applications (e.g. fast response, stable reading, etc.), you can select the optimal filter from wide range of selection.
You could chose either RS-485 (Modbus-RTU/ UNI-format) or SI/F(Unipulse original serial interface) as a standard interface.
＜Fast response＞
F325 processes the analogue peak hold value at the speed of 3000 times/sec. and ouputs HI/OK/LO signal.
It is ideal for the application with short cycle time.
It can be also used for highly accurate weighing system by adjusting A/D conversion speed and/or filter setting.
F325 can be connected to PC via RS-485 or RS-232C, and parameter setting can be edited or saved on PC.
Analog section｜Display section｜External I/O signal｜Interface｜General performance｜Attachments
| Analog section | |
| Excitation voltage |
DC10 or 2.5V±10% (switchable) Output current: within 30mA |
|---|---|
| Signal input range | -3.0 to +3.0mV/V |
| Accuracy |
Non-linearity: 0.02%/FS±1digit (at 3mV/V input) Zero drift: within 0.5μV/℃ RTI Gain drift: within 25ppm/℃ |
| A/D converter |
Speed: 30, 300, 3000 times/sec. (selectable) Resolution: 24bit (binary) |
| Analog filter |
Primary low-pass filter select frequency from 10, 30, 100, 300, 1k, 3k, 10k or 30kHz |
| Digital filter |
Filter 1: Bessel low-pass filter (secondary) Cut-off frequency can be set to any value from 1/300 to 1/10 of sampling speed. It can be turned off. 3000 times/sec.: 10 to 300Hz, 300 times/sec.: 1.0 to 30.0Hz, 30 times/sec.: 0.1 to 3.00Hz Filter 2: Moving average You can set the value anywhere between 1 to 999 times. |
| Resolution | 1/30000 (at 3.0mV/V input) |
| Monitor output | Sensor input of approx. 2V per 1mV/V (Input resistance over 2kΩ) |
| Hold function | Sample or peak hold (You can chose either analogue or digital peak hold from setting menu. Frequency response of analogue hold is 1kHz) |
| Display section | |
| Display unit |
15mm character height: 7-segment green LED (5-digits) Numerical value: 5-digits Indicated value: -19999 to +99999 Decimal points: Selectable decimal point displaying position (0.000, 0.00, 0.0, 0) |
|---|---|
| Display items |
Status display: red 3φLED: HI, LO, PEAK, HOLD green 3φLED: OK Display frequency: selectable from 3, 6, 13 and 25 times/sec. |
| External I/O signal | |
|
External input (3) |
DZ, HOLD, H.RESET ＜Volt-free contact input＞ External devices can be connected, such as relays, switches, transistors and so on. The signal can be outputted by making short-circuit between input and common terminal. In case transistor is connected, please use NPN (sink) transistor. Internal power supply voltage: DC12V, When short-circuited: Approx. 4mA ＜DC-Input for both plus common and minus common type＞ (please specify the type of input when ordering) External devices can be connected, such as relays, switches, transistors and so on. Input signal is outputted by applying voltage between input and common terminal. In case a transistor is connected, please use NPN type for plus common and PNP type for minus common. Maximum Rated Voltage: DC27.6V, “ON”: when the voltage is above DC 9V (Load Current: approx. 10mA at DC24V), “OFF: ” below DC3V. |
|---|---|
|
External output (5) |
HI, OK, LO, Output Selection 1, Output Selection 2 (Assign output from various selection: HH, LL, Overload, RUN, HOLD, NZ, DZ response) PhotoMOS relay output (common for sink and source type) Maximum rated voltage: DC30V, maximum rated current: 100mA, operating time: approx. 1msec |
| Interface | |
|
RS-485 communication interface (Modbus-RTU/ UNI-format) or SI/F (Unipulse original serial interface) BCD parallel data output interface (sink type) (Option) BCD parallel data output interface (source type) (Option) D/A converter (voltage output) (Option) D/A converter (current output) (Option) RS-232C communication interface (Option) |
|
| General performance | |
| Power supply voltage |
AC100V to 240V (+10% -15%) (free power supply) 50/60Hz DC12V to 24V (±15%) (please specify the type of input when ordering) |
|---|---|
| Power consumption | 10W max |
| Rush current(Typ) AC spec. |
2A, 1msec：AC100V average load condition (cold start at room temperature) 4A, 1msec：AC200V average load condition (cold start at room temperature) |
| Rush current(Typ) DC spec. |
2A, 20msec：DC12V average load condition (cold start at room temperature) 1A, 50msec：DC24V average load condition (cold start at room temperature) |
| Operation condition |
Operation temperature range: -10 to +40℃ Storage temperature range: -40 to +80℃ Humidity: 85%RH or less(non-condensing) |
| Dimensions | 96(W)×48(H)×132.5(D)(mm) (not including projections) |
| Panel cutout size | 92×45(+1-0) (mm) |
| Weight | Approx. 600g |
| CE marking certification |
EMC directives: EN61326-1 Safety standard: EN61010-1, EN62311 |
| Attachments | |
|
･ AC input cord * 1 ･ 3P-2P conversion adapter * 1 ･ Terminator (RS-485 is selected) 1 ･ BCD output connector (BCD output option is selected) 1 ･ Operation manual 1 * Included only for AC specifications |
|
| Model | |
| BCO | BCD parallel data output interface (sink type) |
|---|---|
| BSC | BCD parallel data output interface (source type) |
| DAV | D/A converter (voltage output) |
| DAI | D/A converter (current output) |
| 232 | RS-232C communication interface |
|
Product catalogue(PDF)
|
F325 catalogue(581 KB) | |
|---|---|---|
