Optical OEO Repeater: PDH, ATM, SDH, GE, STM-1/4/16, OC-3/12/48: Pilihan Utama di Selangor, Malaysia, Kuala Lumpur (KL), Petaling Jaya (PJ) Catacomm Corporation Sdn Bhd

Penerangan

Description

AN-OEO-2S optical repeat/amplification device，applied in optical repeat prolongation and OEO amplification for transmission equipments. So far the transmission distance of optical access equipments on LAN and access layer is generally short, single mode equipments can hardly go beyond 100km, multimode equipments go even shorter distance, no more than 5km normally. The equipment is requested to solve the solution for fiber optic transmission distance exceed of the equipment transmitting range ability . It can replace expensive optical power amplifier used on network. The increase of transmission distance can be fulfilled through mode of relay. The network can be deployed and business can be open rapidly and conveniently through the equipment. It is equipped with low cost, low power dissipation and small volume. It is the low cost and high performance transmission solution.

Features

A low access optical power，configure output optical power at will access rate can be from 0—2.5G up to 2.5Gb/s.
AN-OEO-2S supports up to 1 channel bidirection or 2 channel unidirection
Support Hot Plug.
Support software update.
Input&Output（Single & multi-mode ,WDM）Multi-wavelength is optional
Single fiber &dual fiber mode is optional.
Maximum transmission distance of data signal is around 120 km.
Accessible to PDH、ATM、POS、GE、STM-1/4/16、OC-3/12/48.

Specifications

Technical parameter：

Property	Description
Input Wavelength	Optional(850nm/1310nm/1550nm)
Output Wavelength	Optional(850nm/1310nm/1550nm)
Output Power Input Sensitivity	Upon hot-swap SFP module

System parameter：

System parameter	Description
Wavelength Range	comply with ITU-T standard
Input Type	PDH 10M/100M/1000M Ethernet STM-16/STM-4/STM-1 OC-48/OC-12/OC-3 64Kb/s–1.25 or 2.5G 2.5Gb/s Adaptive SFP interface
Input interface	Single mode、multi-mode LC/PC
Output interface	Single mode、multi-mode LC/PC
Application	carrier-class /technical grade
Operation Environment	temperature	0-50℃ /-40℃ to 85℃
	humidity	5% to 85%，no condensation
Power Supply	AC 220V，50hz

Panel symbol description：

Symbol	Description
POWER	Power Button
T	（Client Interface LC/PC）SFP Optical Transmitter Interface
R	（Client Interface LC/PC）SFP Optical Receiver
Back Panel CONSOLE RS232	RS232 Network Management Serial Port

Cable connection

Optical cable/electric cable/wire jumper connection description：

wire interface	Quantity	Description
Front Panel T R	Grey1 or 2	（LC/PC）SFP optical transceiver port
Back Panel CONSOLE RS232	1	RS232 Network Management Network Management Serial Port ， Parallel Serial Port Line Connection
Back Panel 220V AC	1	Connect 220V AC power supply

Notes：

Optical ports of the equipment are all LC / PC port, please use the corresponding fiber-optic connections. The definition of all the optical ports are left to send, that is, “T”. Please be careful with the optical power may be greater than-5dbm, escape the direct human eye contact, so as to avoid harm.”R” shows receive which indicates the transmission from the external light source or wire jumper to the devices. Please note that receiving SFP optical power should be less than-3dbm, such as beyond the scope of optical attenuator, connect the equipment to meet the range, in order to avoid equipment damage.

Ordering Information

AN-OEO-2S

Optical repeat/amplification device, with 2 standard SFP slots for SFP modules, AC or DC power as ordering options.

Lebih maklumat tentang Catacomm Corporation Sdn Bhd