No more huge central chassis are needed!
AN-16E1-4ETH-C is the AD-NET multi-E1 convergence-type bridge equipment, it provides 16 E1 and 4 FE interfaces, possesses Channel convergence function, according to the different bandwidth can divide into 1~16 Channel. Each Channel is composed of one or multi-E1 lines, the Channel as the link unit carries the Ethernet data transparently, and it has the function which is similar to EPON, any Channel under the user need can set up isolation or communication. Make use of the Channel as the link unit what is composed of E1 lines can realize point to point or point to multi-point flexible networking, and meet the users’ variety of bandwidth and centralized network management needs.
AN-16E1-4ETH-C not only provides complete alarm instructions of the line side and the Ethernet side, but also provides the error rate statistics, timeout warning, Ethernet traffic statistics management or other exhaustive management information. Network management approach respectively provide based on WEB, PC interface which based on TCP / IP, and library files which based on SNMP to build the SNMP network management that can be unified operation and management.
It can work in pairs as a remote devices with such our converters like AN-E1-ETH, AN-4E1-4ETH-G or AN-8E1-4ETH-G. All the traffic coming from those remote locations then will be concentrated in same central device and in one Ethernet port.
FE interface
10/100BASE-T , full-duplex mode, comply with IEEE802.3 standard.
Support address learning function, the address table size is 2048，Aging time is 5 minutes.
Filter the ultra-long, ultra-short, and CRC error packet.
Support 802.1Q Tag and QinQ function of each Channel.
Support full-duplex PAUSE flow control.
Line interface
Provide 16 E1 interfaces and can be divided into 1 ~ 16 Channel.
Achieve asymmetric transmission in Channel, can be non-paired (a pair means that it is composed of the receiving path and sending path of one E1 port) used.
It can automatically detect the number of available E1 lines and allocate bandwidth in Channel.
It has AIS, LOSS, time-out alarm and bit error rate alarm in Channel; You can inquire the alarm information and bit error rate data through network management.
It supports to set CRC bit error threshold in Channel, when it exceeds the threshold it can automatically cut off the poor quality lines for isolation. You can cut off the error code and set the error threshold by the pin settings or network management.
It allows the maximum propagation delay between any two E1 lines is 64 ms in Channel.
It supports local and remote loop-back of E1 line.
It supports bit error detection and statistics of E1 line.
It has complete line alarm output, automatically processes variety of line anomalies.
Comply with ITU-T G.703 and G.823, but do not support using signaling time slot.
Compatibility
When Channel is composed of 1 E1 line, it is compatible with single E1 bridge device which is achieved through SW1701F, RJ-017, SE0162, SE0163, X-BRIDGE2.0, all standard EOP protocols and standard HDLC protocols
When Channel is composed of two or two more E1 lines, it is compatible with the multi-E1 bridge device what is achieved through SW1602F、SW1604F、SW1605F、 SW1608F、SW1616F、SW1702F and SW1704F or different manufacturers but support the EOP protocol.
| No . | Program | |
| 1 | Input Voltage | -36V ～ -72VDC or 165～265VAC |
| 2 | Power consumption | 9W±10% |
| 3 | Working temperature | 0℃～45℃ |
| 4 | Relative humidity | 95％, no condensation |
| 5 | Atmospheric pressure | 70～106Kpa |
| 6 | Storage temperature | -20℃～70℃ |
|
Program
|
Description
|
| Length × high × wide（depth） | 430mm × 44mm × 185mm |
| Weight | 2.4Kg |
Applications
Type 1: Regular application without VLAN’s
Type 3: application of Tag VLAN (switch)
Examples of management interface (screesnhots):
16E1 central convergence device, E1's can be BNC or RJ-45, dual or single power, AC or DC
| E1 ports | 16 |
Malaysia
