Description
Description
64k-V.35 / V.24 interface converter provides ITU-T co-64K G.703 standard E1 interface and standard V.35 conversion interface between the physical layer / V.24.
The G.703 (Co-Directional G.703) interface divides 64Kbps cycle into 4 unit intervals, it uses“0101” represent “0”, “1100” represent “1″. By alternating transformation polarity of the adjacent block, binary signals convert three-level signals. In every 8th group destroyed block of alternating polarity, thus to transmit 8KHz timing signal. By the above coding, G.703 co-directional 64Kbps signal could achieve transmitting the timing signal of 64KHz and 8KHz and 64KHz and the data signal of 64Kbit/s in the same direction with a pair balanced line.
This interface converter provides one co-directional G.703 interface and one Ethernet interface to achieve 10/100Base-T Ethernet data transmission on the G.703 channel. It is a high performance, self-learning Ethernet bridge. This device is the extension device of Ethernet, using network (PDH/SDH/Microwave) that provide G.703 channel to achieve local and remote Ethernet interconnecting with serial interfaces at a lower cost. The device has inter-set loop test function to facilitate the project launching and daily maintenance.
Features
-
Based on self -copyright IC.
-
Can Realize Ethernet data transmission in one Co-directional G.703 circuit.
-
Inter-set dynamic Ethernet MAC address (4,096) with local data frame filtering.
-
The local device can manage the remote device.
-
Have the function of G.703 loop back check, and indicate on LED.
-
Can differentiate the reason of Co-directional G.703 lose signal is that the remote device power-off or directional G.703 line broken.
-
Ethernet interface supports 10M/100M, half/full duplex auto- adaptable, supports VLAN.
-
Ethernet interface supports AUTO-MDIX (crossed line and straightly connected line self-adaptable ).
-
Provide 2 clock types: Co-Directional G.703 master clock and G.703 line clock.
-
The local device can forced the remote device rate follow it(when the device is unframed mode, that is invalid).
-
Have three Loop Back Mode: G.703 interface Loop Back (ANA)、Ethernet interface Loop Back(DIG)、Command the remote Ethernet interface Loop Back(REM).
-
Support self-adaptable 120 Ohm balance.
Specifications
Interface Standard: comply with protocol ITU-T G.703;
Interface Rate: 64Kbps±50ppm;
E1 Impedance: 120Ω (balance);
Jitter tolerance: In accord with protocol G.742 and G.823
Maximum Transmission Distance: up to 500m
Interface rate: 10/100 Mbps, half/full duplex auto-negotiation
Interface Standard: Compatible with IEEE 802.3, IEEE 802.1Q (VLAN)
MAC Address Capability: 4096
Connector: RJ45, support Auto-MDIX
Working temperature: -10°C ~ 50°C
Working Humidity: 5%~95 % (no condensation)
Storage temperature: -40°C ~ 80°C
Storage Humidity: 5%~95 % (no condensation)
|
Model
|
Model Number: AN-COD-E1
|
|
Functional Description
|
10 / 100M Ethernet data transmission channel in the same direction on the G.703 (Co-Directional G.703), Ethernet rate 64K
|
|
Port Description
|
One co-directional 64K interface, 1 Fast Ethernet interface
|
|
Power
|
Power supply: AC180V ~ 260V；DC –48V；DC +24V
Power consumption: ≤10W
|
|
Dimension
|
Product Size: 216X140X31mm (WXDXH)
|
|
Weight
|
1.2KG
|
Ordering Information
|
AN-COD-E1
|
One co-directional 64K interface, 1 Fast Ethernet interface converter, AC or DC power.
|
More detail about Catacomm Corporation Sdn Bhd
Malaysia
