MASTERCOOL 69900-220 (220-240 V / 50/60 HZ) “MASTERCLEANSE” FLUSH MACHINE: Top Choice in Subang Jaya, Selangor, Kuala Lumpur (KL), Malaysia. Culmi Air-Cond & Refrigeration Parts Supply Sdn Bhd

Description

INTRODUCTION OF MASTERCOOL 69900-220 (220-240 V / 50/60 HZ) “MASTERCLEANSE” FLUSH MACHINE FOR COMPLETE PERFECT FLUSHING OF AIR-COND AND REFRIGERATION SYSTEMS

MASTERCOOL 69900-220 (220-240 V / 50/60 HZ) “MASTERCLEANSE” FLUSH MACHINE = RM3,700.00 PER UNIT (2-9-2021=AA31.40)

OPTIONAL PART NEED TO BUY

MASTERCOOL 91092-A Flush Gun (Flush Gun Assembly W/Rubber Tip) = RM92.00 PER PC * NEED 2PCS (2-9-2021=AA30.65)

SOLVENT

MASTERCOOL 91049-32 OF 32 OZ (0.907185 KG) BOTTLE OF FLUSH SOLVENT (MADE IN USA)

MASTERCOOL 91049-128 1 GALLON (3.78L) BOTTLE OF FLUSH SOLVENT (MADE IN USA) = RM220.00 PER BOTTLE (2-9-2021=AA30.45) * Keep stock!

MASTERCOOL 91049-128-4 OF 4 PACKS OF 1 GALLON (3.78L) BOTTLE OF FLUSH SOLVENT (MADE IN USA) * Keep stock!
Note
. Add clean Mastercool flushing fluid to flushing machine tank by removing the flush fill cap 2 . A minimum of 1 gallon (3.78L) of flushing fluid recommended.

How To Flush AC System After Compressor Failure?
https://carfromjapan.com/article/car-maintenance/how-to-flush-ac-system-after-compressor-failure/

PURGING PROCEDURE

If a purge selection valve is available:

1. Turn the purge selection valve to the preferred purge source.

a. To use an external purge gas source (Nitrogen is preferred. If air is used, the air source must be clean and dry.), attach the gas source to external “PURGE GAS CONNECTION” 11 . The pressure of the external gas cannot exceed 90 PSI (6.2 Bar).

• Turn the purge selection valve 10 to “EXTERNAL AIR/N2”.

b. To use the internal nitrogen source, screw a bottle of nitrogen onto the regulator.

• Turn the selector valve 10 to “INTERNAL N2”.

2. Turn the “FLUSH” valve 8 to a horizontal position as in “Valve Position 2”.

3. Check that all connections are tight.

4. When ready to purge turn the “PURGE” valve 9 to “OPEN”.

5. Continue purging until all of the flush fluid is out of the system and the system is dry.

Product Description

Mastercool introduces its new “MASTERCLEANSE” large volume flush machines designed to flush all HVAC/R and automotive systems. “MASTERCLEANSE” will be commonly used for removal of all solids and residues caused by breakage of compressor or filters. Designed with durable roll-away wheels and handle, this machine can conveniently move as needed.

FEATURES:

Stainless steel ball valve controls
1/4” SAE connection
Additional external container connection
External nitrogen bottle connection
Pump equipped with mechanical seal and PTFE gasket
Mechanical filter present at suction side

SPECIFICATIONS:

Pump Flow Rate: 4 g/min (16 l/min)
Pump Motor: 300 watts
Pump Horsepower: 110V/60 Hz – 0.4 HP or 220-240V/50/60 Hz – 0.28 HP
Full Load Amperage: 110V/60 Hz – 2.4 amps or 220-240V/50/60 Hz – 1.7 amps
Flush Container: 2.6 gal (10 l)
Hoses: 9 ft (3 m) flexible, clear coiled
Dimensions: 15” (l) x 16” (w) x 24” (h) /with handle extended 36” (h) (381 mm (l) x 406 mm (w) x 609 mm (h) /with handle extended 914 mm (h))
Weight: 42 lbs (19 kg)

Application

Yes, the system is suitable for large VRF systems. Probably more so than automotive. The unit will push the flush agent through a system that has a return route. You can continually fill the reservoir until the system is fully flooded with flush. The unit will have a push pressure from the pump but it is not intended to pressurise the system. The system needs to be an open circuit. 30 meters pipe length is easily handled. It is recommended that nitrogen be used to clear the system of residual flush agent when flushing is complete.

More detail about Culmi Air-Cond & Refrigeration Parts Supply Sdn Bhd