Compatible with the most common leading-edge and trailing phase dimmers
Flexible current setting (DIPswitch - 2 to 4 currents)
Flicker-free dimming
Higher quality of light thanks to < 5% output ripple current
Areas of application
Decorative illumination
Downlights, flat luminaires
Hospitality
Living areas
Museums, residential buildings
Offices
Shop lighting
Suitable for indoor SELV installations
Suitable for luminaires of protection class I and II
Electrical data
Nominal input voltage : 220…240 V
Mains frequency : 50/60 Hz
Input voltage AC : 198…264 V
Total harmonic distortion : < 20 %
Power factor λ : > 0.95
Efficiency in full-load : 82 %
Device power loss : 4.0 W
Protective conductor current : <0.7 mA
Inrush current : < 10 A
Max. ECG no. on circuit breaker 10 A (B) : 33
Max. ECG no. on circuit breaker 10 A (C) : 55
Max. ECG no. on circuit breaker 16 A (B) : 53
Max. ECG no. on circuit breaker 16 A (C) : 88
Max. ECG no. on circuit breaker 25 A (B) : -
Surge capability (L/N-Ground) : 2 kV
Surge capability (L-N) : 1 kV
Nominal output voltage : 27…40 V
U-OUT (working voltage) : 60 V
Nominal output current : 225/325/350/450 mA
Output current tolerance : ±7.5 %
Output ripple current (100 Hz) : < 5 %
Output PSTLM : ≤ 1
Output SVM : ≤ 0.4
Nominal output power : 18 W
Maximum output power : 18 W
Galvanic isolation primary/secondary : SELV
Current set : DipSwitch
Default output current : 450 mA
Product weight : 77.70 g
Cable cross-section, input side : 0.75...1.5 mm²
Cable cross-section, output side : 0.75...1.5 mm²
Wire preparation length, input side : 5...6 mm
Wire preparation length, output side : 5...6 mm
Length : 95.0 mm
Width : 50.0 mm
Height : 22.0 mm
Temperatures & operating conditions
Ambient temperature range : -20…+50 °C
Maximum temperature at tc test point : 80 °C
Max.housing temperature in case of fault : 110 °C
Temperature range at storage : -20…+80 °C
Permitted rel. humidity during operation : 5…85 %
Lifespan
ECG lifetime : 30000 / 50000 h
Capabilities
Dimmable : Yes
Dimming interface : Phase cut
Dimming range : 5…100 %
Dimming method : Amplitude Modulation
Overheating protection : Automatic reversible
Overload protection : Automatic reversible
Short-circuit protection : Automatic reversible
No-load proof : Yes
Intended for no-load operation : No
Max. cable length to lamp/LED module : 2.0 m
Suitable for fixtures with prot. class : I / II
Type of connection, input side : Push terminal
Type of connection, output side : Push terminal
Suitable for through-wiring : No
Number of channels : 1
Certificates & standards
Approval marks – approval : CE / CCC / ENEC / EAC / RCM
Standards : Acc. to IEC 61347-1/Acc. to IEC 61347-2-13/Acc. to IEC 62384/Acc. to CISPR 15/Acc. to IEC 61000-3- 2/Acc. to IEC 61000-3-3/Acc. to IEC 61547
E S L Lighting (M) Sdn BhdLED Lighting Supplier Selangor, Lighting Shop Seri Kembangan, Kuala Lumpur (KL), Decorative Lighting Supplies Malaysia ~ E S L Lighting (M) Sdn Bhd