F701-C is a general-purpose weighing controller that is compatible with all weighing systems. This is a practical device excellent in cost effectiveness, which is equipped with the final discharge function allowing high-accuracy feeding and discharging weighing control and the weighing sequence function essential to hopper and packing scales.
Installable is the interface that can be connected to PLCs or various peripherals such as BCD output, RS-232C and CC-Link.
| Analog section | |
| Excitation voltage |
10V DC ±5%, Output current; within 120mA (Up to 4 loadcells at 350Ω are parallel-connectable) |
|---|---|
| Zero adjustment range |
0 to 2mV/V Rough adjustment: Digitally controlled via rough adjustment circuit Fine adjustment: Auto adjusting method via digital processing |
| Gain adjustment range |
0.3 to 3.2mV/V Rough adjustment: Digitally controlled via rough adjustment circuit Fine adjustment: Auto adjusting method via digital processing |
| Min. input sensitivity | 0.3μV/count |
| Accuracy |
Non-linearity: within 0.01% FS Zero drift: within 0.2μV/°C RTI Gain drift: within 15 ppm/°C |
| Analog filter |
Bessel low-pass filter (-12dB/oct.), Selectable from 2, 4, 6, 8 Hz |
| A/D converter |
Speed: 200 times/sec. Resolution: 24 bit (binary) |
| Setting section | |
| Setting items |
– High limit, Low limit, near zero, SP1, SP2, Compensation, over, under, final ･ Comparison inhibit time, judging time, complete output time, adjust feeding time, auto zero times, judging times. Auto free fall compensation regulation, analog filter, tare weight ･ Weighing function 1, weighing function 2, weighing function 3, sequence mode, function key inhibit, digital filter, motion detect, zero tracking period, zero tracking range ･ Balance weight value, capacity, min. scale division, net over, gross over, DZ regulation value, function selection, gravitation acceleration (area number input), gravitation acceleration (acceleration input) ･ D/A output mode, D/A zero output weight, D/A full scale, RS-485 I/F, ID number, RS-232C I/F, external function selection, setting value LOCK, restriction on the tare subtraction function ･ Input selection, output selection, CC-Link I/F Occupied station & Transmission speed, CC-Link I/F Station No. ･ Average weight, maximum weight, minimum weight, population standard deviation, sample standard deviation, number of data (n), latest accumulation date, Maximum-minimum (R), option substrate ･ Span calibration, equivalent input calibration, password input, zero calibration |
|---|---|
| I/O section | |
| External input signal |
･ ON when shorted to COM terminal by contact (relay, switch) or non contact (TTL-level transistor or open collector output) ･ G/N, digital zero, tare subtraction ON, tare subtraction OFF, hold*, judge*, feed / discharge, start*, stop*, accumulation command*, accumulation clear* * Signals for selection. Up to 4 can be selected. |
|---|---|
| External output signal |
･ Transistor’s open collector output (Emitter = COM terminal); Output is LO when transistor is ON. ･ Near zero, SP1, SP2, SP3, under, over, Low limit, high limit, stable, weight alarm or error, go or complete, run or accumulation error |
| Interface |
･ SIF: 2-wire type serial interface (standard); Interface to link with Unipulse printer or external display ･ 232: RS-232C communication interface (standard): Write (change)/read weight data, various statuses and setting values by commands from a host computer ･ BCO: BCD parallel data output interface (Optional): Parallel interface to transmit weight data to various peripherals ･ 485: RS-485 communication interface (Optional): Allows longer-distance communication than RS-232C. ID numbers are set, and multiple units of F701-C are parallel-connectable. ･ DAC: D/A converter interface (Optional); Interface to convert weight data to current signal and output it. ･ CCL: CC-Link interface (Optional); Links directly to PLC. |
| Display section | |
| Display unit | Numerical display (7 digits) with a character height of 10.4 mm by fluorescent display tube, Sub-display; character height 4.0 mm |
|---|---|
| Display value | 5 digits, Sign; Minus sign displayed on most significant digit |
| Unit | Selectable from t, kg, g, N, lb, none |
| Status display | SP1, SP2, SP3, NEAR ZERO, HOLD, ZERO ALARM, STAB, TARE, NET, ZERO, BATTERY CONDITIONS |
| General performance | |
| Power supply voltage | 100 to 240V AC (+10% -15%) (Free power supply 50/60 Hz) |
|---|---|
| Power consumption | Approx. 15VA |
| Operating conditions |
Temperature: Working temperature range -10 to +40°C; Storage temperature range -20 to +85°C Humidity: 85% RH or less (non-condensing) |
| Dimensions | 144(W)×72(H)×160(D) mm (protruding parts not included) |
| Weight | Approx. 1.0kg |
| Attachments | |
| AC input cord (nominal rating: 125V) 3m | 1 |
|---|---|
| Mini-driver | 1 |
| FCN series I/O connector (with cover) | 1 |
| Jumper cable | 2 |
| Operation Manual | 1 |
| BCD output connector (when BCD output option is installed) | 1 |
| RS-485 connector (when RS-485 option is installed) | 1 |
| D/A converter connector (when D/A converter option is installed) | 1 |
| CC-Link connector (when CC-Link option is installed) | 1 |
whatsapp us now !
