30F131

30F131

Category: Available (Qty:9999999)
For more information, visit our official website at utsource.us

Description

BUY 30F131 https://www.utsource.net/itm/p/12380440.html

Parameter Symbol Min Typ Max Unit Description
Supply Voltage VDD 2.0 - 5.5 V Operating supply voltage range
Operating Temperature Toper -40 - 85 掳C Operating temperature range
Storage Temperature Tstg -65 - 150 掳C Storage temperature range
RAM Size 32 KB Internal RAM size
Flash Memory 128 KB Program memory size
EEPROM Size 4 KB Data memory size
I/O Pins 32 Number of I/O pins
Timer Modules 5 Number of timer modules
ADC Channels 12 Number of analog-to-digital converter channels
UART Modules 2 Number of UART modules
SPI Modules 2 Number of SPI modules
I2C Modules 2 Number of I2C modules
PWM Channels 10 Number of PWM channels
Watchdog Timer 1 Watchdog timer module
Brown-Out Reset BOR 1.8 - 4.6 V Brown-out reset threshold
Oscillator Frequency fOSC 0 - 32 MHz Maximum oscillator frequency

Instructions for Using the 30F131 Microcontroller:

  1. Power Supply:

    • Ensure the supply voltage (VDD) is within the range of 2.0V to 5.5V.
    • Use appropriate decoupling capacitors (typically 0.1渭F and 10渭F) close to the power pins to reduce noise.
  2. Operating Temperature:

    • The microcontroller can operate between -40掳C and 85掳C. Ensure the operating environment does not exceed these limits.
  3. Storage Temperature:

    • Store the microcontroller in an environment between -65掳C and 150掳C to prevent damage.
  4. Memory Management:

    • Utilize the 32KB of internal RAM for data storage and processing.
    • Use the 128KB of flash memory for program storage.
    • Store critical data in the 4KB EEPROM for non-volatile storage.
  5. I/O Configuration:

    • Configure the 32 I/O pins as inputs or outputs based on your application requirements.
    • Use internal pull-up resistors if necessary.
  6. Timer Modules:

    • Configure the 5 timer modules for various timing and counting tasks.
    • Set up timer interrupts for periodic events.
  7. ADC Configuration:

    • Use the 12 ADC channels to read analog signals.
    • Configure the ADC resolution and sampling rate as needed.
  8. Communication Interfaces:

    • Use the 2 UART, 2 SPI, and 2 I2C modules for serial communication with other devices.
    • Configure baud rates, data formats, and other settings according to the communication protocol.
  9. PWM Generation:

    • Utilize the 10 PWM channels for generating pulse-width modulated signals.
    • Configure the PWM frequency and duty cycle as required.
  10. Watchdog Timer:

    • Enable the watchdog timer to reset the microcontroller if it hangs or malfunctions.
    • Set the watchdog timer period to an appropriate value.
  11. Brown-Out Reset:

    • Enable the brown-out reset feature to reset the microcontroller if the supply voltage drops below the threshold (1.8V to 4.6V).
  12. Oscillator Configuration:

    • Choose an external crystal or resonator for the oscillator.
    • Ensure the oscillator frequency is within the supported range (0 to 32 MHz).
  13. Programming and Debugging:

    • Use a suitable programmer and development environment (e.g., MPLAB X IDE) to write and debug code.
    • Follow the programming guidelines provided by the manufacturer.

By following these instructions, you can effectively utilize the 30F131 microcontroller in your projects.

(For reference only)

More detail about Utsource Holding Company Limited
Utsource Holding Company Limited
Utsource Holding Company Limited Electronic Component Wholesaler, IC Chip Distributor, IGBT Module Supplier in California, USA | Utsource Holding Company Limited