LPV-60E: Top Choice in Selangor, Malaysia, Kuala Lumpur (KL), Shah Alam Winston Resources

Description

Features:
‧Constant voltage design
‧Universal AC input / Full range
‧Withstand 300VAC surge input for 5 seconds
‧Protections: Short circuit / Overload / Over voltage
‧Cooling by free air convection
‧Fully encapsulated with IP67 level(Note.8)
‧Fully isolated plastic case
‧Class II power unit, no FG
‧Class 2 power unit
‧Pass LPS
‧Suitable for LED lighting and moving sign applications(Note.7)
‧100% full load burn-in test
‧Low cost, high reliability
‧3 years warranty

Model		LPV-60E-5	LPV-60E-12	LPV-60E-15			LPV-60E-24
Output	DC voltage	5V	12V	15V			24V
	Rated current	8A	5A	4A			2.5A
	Current range	0~8A	0~5A	0~4A			0~2.5A
	Rated power	40W	60W	60W			60W
	Ripple&noise (max.)	80mVp-p	120mVp-p	120mVp-p			150MVp-p
	Voltage tolerance	±8.0%	±5.0%
	Line regulation	±1.0%
	Load regulation	±6.0%	±2.0%
	Setup,rise time	500ms, 20ms / 230VAC 500ms, 20ms / 115VAC at full load
	Hold up time	50ms/230VAC 16ms/115VAC at full load
Input	Voltage range	90 ~ 264VAC 127 ~ 370VDC
	Frequency range	47 ~ 63Hz
	Efficiency	76%	83%			83%	86%
	AC current	1.2A/115VAC 1A/230VAC
	Inrush current	COLD START 60A(twidth=525£g s measured at 50% Ipeak) at 230VAC
	Leakage current	0.25mA/240VAC
Protection	Overload	110 ~ 150% rated output power
		Protection type：hiccup mode，auto-recovery after fault condition is removed
	Over voltage	5.75~ 6.75V	13.8~ 16.2V		17.5~ 20.25V		27.6~32.4V
		Protection type : Shut off o/p voltage, clamping by zener diode
Environment	WORKING TEMP.	-30 ~ +70℃ (Refer to "Derating Curve")
	Working humidity	20%~90%RH non-condensing
	Storage temp,humidity	-40℃~+80℃,10%~95%RH
	Temp. coefficient	±0.03%/℃ (0 ~ 50℃)
	Vibration	10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
Safety&EMC	Safety standard	UL879(except for LPV-60-5), UL1310(except for LPV-60-5), CSA C22.2 No. 207-M89(except for LPV-60-5, LPV-60-48),CAN/CSA C22.2 No. 223-M91(except for LPV-60-5,LPV-60-48), IP67 approved ; design refer to TUV EN60950-1
	Withstand voltage	I/P-O/P:3KVAC
	Isolation resistance	I/P-O/P:>100M Ohms / 500VDC / 25℃/ 70% RH
	EMC emission	Compliance to EN55022 (CISPR22) Class B, EN61000-3-2 Class A, EN61000-3-3
	EMC immunity	Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A
Others	MTBF	705Khrs min. MIL-HDBK-217F (25℃)
	Dimension	162.542.532mm (LWH)
	Packing	0.41Kg; 40pcs/16.5Kg/0.56CUFT

NOTE:
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 ℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
7. Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minute.
8. The unit might not be suitable for lighting applications in EU countries. Please check with your local authorities for the possible use of the unit.

More detail about Winston Resources