Sensor input for torquePulse input for rotation speedDisplay sectionExternal I/O sectionGeneral performanceAttachments
| Sensor input for torque (voltage input) | |
| Input resistance | 1MΩ |
|---|---|
| Signal input range |
±10V(UTM/UTF(Option)) ±5V(UTM/UTMV) |
| Accuracy |
Non-linearity : Within 0.02%/FS±1digit Zero drift : Within 0.2mV/ RTI Gain drift : Within 0.01%/ |
| A/D converter |
･ Speed…16000 times/sec. ･ Resolution…24bit (binary) Approx. 1/30000 with respect to 10V |
| Digital low pass filter | PASS, 3 to 1kHz. |
| Digital high pass filter | PASS, 3 to 1kHz. |
| Voltage output | Input voltage cuff (For test point) |
| Rotation speed input for high speed (Pulse input, open collector) | |
| Maximum input frequency | Based on UTM/UTMV/UTM/UTF |
|---|---|
| Minimum input frequency |
Select from 15, 10, 5, 3, or 2 rpm (when pulse rate is 4 ppr) Select from 60, 40, 20, 12, 8 rpm (when pulse rate is 1 ppr) |
| Minimum detection pulse width | 50μs |
| Circuit configuration |
No-voltage contact input (minus common) Open collector connectable (IcApprox. 10mA) |
| Rotation speed input for low speed(Pulse input, open collector) | |
| Maximum input frequency | Approx. 1000rpm |
| Minimum input frequency | 0.1rpm |
| Minimum detection pulse width | 5μs |
| Circuit configuration |
No-voltage contact input (minus common) Open collector connectable (IcApprox. 10mA) |
|
Encoder input(Pulse input) Compatible with encoder option of UTM/UTM |
| Display section | |
| Display |
Main display : Character height 15mmNumerical display by 7-segment green LED (5-digit+sign) Sub display : Character height 8mmNumerical display by 7-segment green LED (5-digit) |
|---|---|
| Indicated value |
Main display : 5-digit -99999 to +99999 Signs : Minus sign on most significant digit Sub-display (Rotation speed) : 5 digit 0 to +99999 Sub-display (Angle) : -19999 to +19999 Signs : Minus sign on most significant digit |
| Decimal point |
0, 0.0, 0.00, 0.000 (torque) 0(Rotation speed Low-speed rotation mode 0.0) 0, 0.0, 0.00(Angle Depending on unit and min. scale division setting) |
| Display frequency | Selectable from 3, 6, 13, and 25 times/sec. |
| Status display | HI / LO / HOLD |
| Unit | rad/deg (Depending on angle unit setting) |
| Hold |
Sample, Peak, Valley, P-P, Average Hold section setting (All section・External signal・External signal+Time・Level+Time) |
| External I/O section | |
|
External input (5) |
Hold control / Hold reset / Digital Zero / Angle zero clear/ Record data clear Dry contact input circuit (minus common type), Ic10mA or less |
|---|---|
|
External output (13) |
HI/LO limit comparison (alarm HI・HI・OK・LO・alarm LO) / Hold complete / RUN Timing output/ Absolute value display Open collector output circuit (sink type), Vceo30V (max) Ic30mA (max) |
| Interface |
SIF : 2-wire serial interface 485 : RS-485 interface (Specifically for UTM/UTF) BCO : BCD parallel data output interface (Option) 232 : RS-232C communication interface (Option) D3V : D/A converter voltage output(3ch) (Option) DAV : D/A converter voltage output (Option) DAI : D/A converter current output (Option) USB : USB interface (Option) * Only one option can be installed. |
| General performance | |
| Power supply voltage | ±DC24V |
|---|---|
| Power consumption | 8W typ. |
| Operating conditions |
Operation : -10 to +50桡Storage-40 to +80 Humidity : 85%RH or less(non-condensing) |
| Dimensions | 96(W)×96(H)×138(D) mm (Projections excluded) |
| Panel cutout size | 92×92(+1-0)mm |
| Weight | Approx. 1.2kg |
| CE marking certification | EMC directives EN61326-1 |
| Attachments | |
|
Operation manual･･････1 External input/output connector･･････1 Unit seal･･････1 Connector for BCD output (with BCD output option)･･････1 Operating tool (with D/A converter(3ch) option)･･････1 Mini screwdriver (with D/A converter option)･･････1 Ferrite core･･････1 |
|
| Sign | Specification |
| Standard |
UTM/UTM/UTMV *Cannot be connected simultaneously. |
|---|---|
| UTF |
UTF (Optional specification) *UTM/UTM/UTMV cannot be connected. |
| Model | Description |
| CA372-I/O | Cable with FCN connector at one-end 3m |
|---|---|
| CA81-USB | miniUSB-computer USB cable 1.8m |
| CATM321-M | Cable for UTM/UTF connection 2m |
| CATM351-M | Cable for UTM/UTF connection 5m |
| CATF-COM-2M-M | Communication cable for UTF 2m |
| CATF-COM-5M-M | Communication cable for UTF 5m |
| CATM221-MC | Cable for UTM/UTMV connection 2m |
| CATM251-MC | Cable for UTM/UTMV connection 5m |
| CATM(R)321-M | Cable for connecting UTM rotary encoder 2m |
| CATM(R)351-M | Cable for connecting UTM rotary encoder 5m |
| CATM(R)321-MR | Cable for connecting UTM rotary encoder 2m |
| CATM(R)351-MR | Cable for connecting UTM rotary encoder 5m |
| CN34 | D-Sub9p connector for RS-232C |
| CN50 | FCN series I/O connector (with cover) |
| CN51 | BCD output connector |
| CN55 | FCN series I/O connector (with diagonal cover) |
| CN73 | D/A converter(3ch) connector |
| CN92 | UTM connector |
| CN93 | UTM rotary encoder connector |
| DTC2 | Case for TM380 |
| GMP96x96 | Rubber packing |
| E04SR211132 | Ferrite core |
| TSU03 | Lightning surge protector (DC) |
|
Product catalogue(PDF)
|
TM380 catalogue(682 KB) | |
|---|---|---|
Malaysia
