PH10M

Description

PH10M (Fully Motorised Probe Head)

Like the PH10T probe head, the PH10M is also a fully motorised probe head that offers immediate indexing from 0° to 105° in the A axis and through 360° in the B axis, in 7.5° increments. The M head, however, incorporates an autojoint with multiwire capability, which is necessary for the SP25M scanning probe. The PH10M probe head can also be fitted with either TP20 or TP200 probes and should be chosen in preference to the PH10T when using these probes if the future use of a scanning technology may be required.
 

Length	117 mm
Width	62 mm
Weight	620 g
Probe mounting	Autojoint (multiwire)
Head mounting	PH10M PLUS shank to suit CMM
Suitable controller	PHC10-3 PLUS
Repeatability of position	0.4 µm (0.00002 in) specified at a distance of 100 mm
Total number of positions	720
Maximum recommended drive torque	0.45 Nm
Maximum extension bar	300 mm (11.8 in) using PAA3 extension 450 mm (17.7 in) using PAACF special order only extension

_______________________________________________________________________________________________________________________________________________________________________

TP20 Stylus Modules

A range of seven, application specific, probe modules is available and are identified by coloured caps.

Module		Application	Trigger forces*	Stylus lengths
SF- Standard force		Suited to the majority of applications	XY: 0.08 N Z: 0.75 N Stylus: 10 mm	10 mm to 50 mm GF
LF- Low force		Low trigger forces applications - e.g. rubber seals	XY: 0.055 N Z: 0.65 N Stylus: 10 mm	10 mm to 30 mm
MF- Medium force		Where a higher trigger force than standard is required	XY: 0.1 N Z: 1.9 N Stylus: 25 mm	10 mm to 60 mm
EF- Extended force		Large stylus assemblies or where vibration causes spurious 'air' triggers	XY: 0.1 N Z: 3.2N Stylus: 50 mm	10 mm to 60 mm
6W- 6-way		Measurement in the –Z direction - e.g. undercuts	XY: 0.14 N Z: 1.6N Stylus: 10 mm	10 mm to 30 mm
EM1 STD- 50 mm extension		Majority of applications requiring a 50 mm extension	XY: 0.08 N Z: 0.75 N Stylus: 10 mm	10 mm to 50 mm
EM2 STD- 75 mm extension		Majority of applications requiring a 75 mm extension	XY: 0.08 N Z: 0.75 N Stylus: 10 mm	10 mm to 50 mm

Change Rack MCR20
The MCR20 probe module changing rack is designed to securely hold stored modules for rapid automatic changing, and to protect them from airborne contaminants which may be present within the working environment.



_______________________________________________________________________________________________________________________________________________________________________

TP200 Stylus Modules

The stylus module is mounted on the TP200 / TP200B probe body via a highly repeatable magnetic kinematic joint, providing a rapid stylus changing capability and probe overtravel protection.
There are three modules available, with two different overtravel forces.

Module	Application	Comments
SF (standard force)	General use.	Styli up to 100 mm long and ball diameter > 1 mm.
LF (low force)	Small diameter stylus balls or where minimum force is essential.	Balls less than 1 mm diameter.
EO (extended overtravel)	Extra overtravel to enable the CMM to stop safely from higher probing speeds.	Same overtravel force as SF. Extra 8 mm of overtravel in probe Z-axis.

SCR200 Change Rack
The SCR200 provides automatic, high speed changing of up to six TP200 stylus modules. The SCR200 is powered by the separate probe interface, PI 200-3, and provides features to facilitate safe stylus changing. The SCR200 is available in low force and standard force kits, where each kit comprises one SCR200 plus three stylus modules of the same force.

 

 

More detail about VGSM Technology (M) Sdn Bhd