F701-P Global standard model basic performance design weighing indicator

F701-P Global standard model basic performance design weighing indicator

Category: weighing indicator Available
For more information, visit our official website at ims.com.my

Description

F701-P is a weighing indicator with convenient functions and operability for weighing such as a high-precision amplifier, fast-sampling, High-Low limit comparison function, weighing function and accumulation functions.

Analog section
Excitation voltage DC5V±5% Output current: within 90mA
Ratio metric type (Up to six 350Ω load cells can be connected in parallel.)
Signal input range -0.5 to 3.0mV/V
Zero adjustment range Automatic adjustment by digital operation
-0.2 to 2.0mV/V
Span adjustment range Automatic adjustment by digital operation
0.3 to 3.0mV/V
Minimum input sensitivity 0.15μV/count
Accuracy Non-linearity: within 0.01%/FS
Zero drift: 0.025μV/℃ RTI typ
Gain drift: 1ppm/℃ typ
A/D converter Conversion rate: 300 times/sec.
Conversion resolution: 24bit (binary)
Minimum indication resolution 1/10000
 
Setting section
Setting method Settings are made by operating the membrane keys.
Also, settings can be made from a host computer through the RS-485 interface.
Memory of set value F-RAM (nonvolatile RAM)
Protect of set value Software LOCK can be set to parameter such as “Set value” and “Calibration”.
Setting items

Upper limit/ Lower limit/ Near zero/ Set point 1/ Set point 2/ Compensation/ Over/ Under/ Final/ Comparison inhibit time/ Judging time/ Complete output time/ Weighing function 1/ Weighing function 2/ Tare setting/ Tare display/ Digital low pass filter/ Moving average filter/ Motion detection/ Zero tracking (Period)/ Zero tracking (Range)/ Total comparison selection/ Total limit (high 4 digit)/ Total limit (under 5 digit)/ Count limit/ Key invalid/ LOCK/ Input selection/ Output selection/ Password/ Balance weight value/ Capacity/ Min. scale division/ DZ regulation value/ Display selection/ Gravitational acceleration/ Zero calibration/ Span calibration/ RS-485 I/F setting/ Communication type/ RS-485 ID/ Transmission delay time

 
External signal (You can specify whether PNP (Source) type or NPN (Sink) type when order the F701-P.)
Output signals (4) Select from COMPL./ SP1/ SP2/ SP3/ HI/ GO/ LO/ STAB/ WEIGHT ERROR/ TOTAL FINAL
At signal ON, output transistor ON.
* External External voltage must be prepared separately by customer.
Input signals (4) Select from G/N/ D/Z ON/ TARE ON/ TARE OFF/ ACCUMULATION CLEAR/ HOLD/ JUDGE
Contact (relay, switch etc.) or non-contact (transistor, open collector etc.) can be connected.
* External voltage must be prepared separately by customer.
Interface 485: RS-485 communication interface (Select from Modbus-RTU and original format)
 
Display section
Display 18.5mm in character height, Numerical display on LCD (7 digit)
Sub display: 7.3mm in character height (14 digit)
Indicated value 5 digit sign: negative display at the highest digit
Accumulation value 9 digit
* This can be changed to “Accumulation count (4 digit)” and “Final(5 digit)”.
Display frequency Select from 1, 2, 5, 10, 20 times/sec. (The system speed is 300 times/sec.)
Capacity 5 digit
Min. scale division Setting allowable in the range of 1 to 50
Decimal point Select from 0, 0.0, 0.00, 0.000
Over display LOAD: A/D converter input over,
OFL1: Net over,
OFL2: Capacity +9 scale division,
OFL3: Gross over
Center zero A true zero point or the center of each value is displayed.
Status display COMPL./ SP3/ SP2/ SP1/ HI/ GO/ LO/ ZT/ NZ/ HOLD/ ZALM/ STAB/ TARE/ NET/ GROSS/ CZ
 
General performance
Power supply voltage AC100 to 240V (+10% -15%)(free power source 50/60Hz)
Power consumption Approx. 5W
Inrush current 1.5A, 0.7mSec: AC100V average load condition (cold start at room temperature)
2.5A, 0.7mSec: AC200V average load condition (cold start at room temperature)
Operating conditions Temperature…Operation -10℃ to +40℃, Storage -20℃ to +85℃
Humidity…85% or less (non-condensing)
Dimensions 192(W)×96(H)×102(D) mm (Projections excluded)
Panel cutout dimensions 186(+2-0)(W)×92(+1-0)(H)mm
* Installation panel thickness: 2.0 to 3.2mm
Weight Approx. 1.3kg
 
Attachments
AC input cord (Nominal rating 125V) 3m 1
Jumper line 2
Terminator 1
Operation manual 1
Rubber packing 1

iMS Motion Solution (Johor) Sdn Bhd (Company Registration 1098771-W)
 
No.7, Jalan Sasa 4,Taman Gaya, 81800 Ulu Tiram, Johor Bahru, Johor. Malaysia.
TEL:+607-8635240 FAX: +607-8637240
MOBILE: +6019-6774477
EMAIL: [email protected]WhatsApp  | www.ims.com.my
HOTLINE : 1700-818-330
whatsapp us now !

Brand Name
MEISTER | GGM | Sanyo Denki | ElectroCraft | EDrive | SHIHLIN ELECTRIC | AUTONICS | UI Robot | Mitsubishi CNC | PANASONICApex Dynamics | NISSEI GTR | UNIPULSE | CREVIS
 
MOTION DEVICES SPECIALIST | SYSTEM and CONTROL INTEGRATION |
| Induction Motor | Speed Control Motor | Reversible Motor |Brake Motor |BLDC Motor |DC Motor |Planetary Gear Motor | Servo Motor | Stepping Motor | Linear Actuator Motor | Lead Screw Motor|Close Loop Stepping Motor | Customization Motors | Right Angle Gear Head | Precision Gear Reducer |PLC | Motion Controller |HMI /Touch Screen| Inverter |CNC Controller |Multi Axis Robots |IPC | SCADA |Monitoring Software | Embeded PC | Remote IO |TPC | Motion Card | Loadcell |PPC |
 
Return / Refund Policy : 
All goods sold are not returnable & we accept goods ex-change with equal or lower value of good purchased. If the ex-change items are higher than purchased items, buyer shall top up the differential cost. All payment made are not refundable, please confirm the purchase items code & cost with our sales representative before place orders.
 
Shipping and Fulfillment :
Thank you for your purchase. Once we have confirmed your payment, we will prepare and ship out your order out within 24-48 hours.( For ex-stock items only, Indent items subject to delivery stated in quotation & conversation in emails). Once your order has been shipped out, you will receive an email notification with the tracking number and tracking details inside.
 
Private Policy
General Statement of Principles 
As described in detail below, any information we gather at this web site is strictly for our use and is not shared with any other entity, public or private, for any reason - period. We will not sell or give away any lists or other data that we may retain and we do not purchase such information from other sources.
Statistical Data 
Our servers (as most) track IP addresses and referring pages to help with site maintenance and improvements. This data is viewed only as anonymous statistics to show the busiest times of the day or week, pages with errors and how effective our advertising has been. This information is not used for any other purpose.
Personal Information Collected - Order Forms
With the exception of credit card info, we store the information from your order form to allow us to track consulting issues or refer to a previous order to help provide some customer service. You may elect to have your information completely removed from this system by e-mailing us at [email protected] with your request. We do not store any type of sales information.
Information Correction or Removal 
If you wish to correct, update or remove any information about you that may be in our records, please send us e-mail at [email protected] with the details of your request. If you wish to contact us further, please find complete contact information on our contact page.
Cookies
Cookies are files with small amount of data, which may include an anonymous unique identifier. Cookies are sent to your browser from a web site and stored on your computer's hard drive. We use 'cookies' to store your cart contents for you. You can instruct your browser to refuse all cookies or to indicate when a cookie is being sent. However, if you do not accept cookies, you may not be able to use the checkout section of our site.
 
Changes To This Privacy Policy
This Privacy Policy is effective as of 1st Jan 2019 and will remain in effect except with respect to any changes in its provisions in the future, which will be in effect immediately after being posted on this page.

More detail about IMS Mechatronics Sdn Bhd
IMS Mechatronics Sdn Bhd
IMS Mechatronics Sdn Bhd Motion Solutions Johor, Control Components Supplier Malaysia, Motion Devices Johor Bahru (JB) ~ IMS Mechatronics Sdn Bhd
Contact Us flagMalaysia