i-Vu® Zone Ctrl II OPN-B3-P-02: 马来西亚的首选 United Faith Sdn Bhd

详情

Product-Integrated Controller

The Zone Controller II provides zone level control for a variety of pressure-independent VAV and pressure dependent VVT applications. This completely programmable advanced controller features a separable actuator for easy installation onto fan-powered or single-duct air terminals. It also features native BACnet communications and plug-and-play connectivity to the Carrier i-Vu Building Automation System.

Application Features

A library of sophisticated factory-engineered and tested control programs provide reliability and energy efficiency
Programmable zone level control of terminal units, fan coils, lighting, exhaust fans and more
Supports advanced control routines for zone level humidity control or zone level demand control ventilation (ASHRAE® 62)
Supports Carrier communicating space sensors and touch screens which allow for local setpoint adjustment and local overrides
Quick and easy test & balancing process

System Benefits

Integrated Carrier airside linkage algorithm for plug-and-play integration with Carrier air sources
Fully plug-and-play with the Carrier i-Vu Building Automation System
Supports demand limiting for maximum energy savings
Supports dual duct applications when used with Carrier’s VAV Zone II Secondary Terminal Controller

Hardware Features

Separable brushless actuator for reliability and longevity
Capable of system or stand-alone operation
Native BACnet MS/TP or ARCNET communications
Controls up to 8 points (3 binary outputs, 4 universal inputs and 1 analog output)

BACnet Support	Advanced Application Controller (B-AAC), as defined in BACnet 135-2012 Annex L Protocol rev. 9
Communication Ports	BACnet Port: EIA-485 port for BACnet MS/TP communications (9600 bps, 19.2 kbps, 38.4 kbps, & 76.8) or ARCNET 156 kbps; Local Access Port: For system start-up and troubleshooting (115.2 kbps) Rnet Port: For connecting Carrier communicating room sensors and Carrier’s touchscreen user interface ARCnet Port: For connecting the actuator cable
Separable Actuator	Brushless DC motor, torque 45 inch-pounds (5Nm), runtime 205 seconds for 90 degree travel during control.
Integral Pressure Sensor	Precision low flow AWM series O-2 in H2O, sensitive down to +/-0.001 in. H2O. Barbed tapered airflow connections accept 3/16 in. (4.75 mm) ID tubing. Allows for readings across the 0-2 in H2O range, accurate to +/-5% of full flow at 2 in. H2O.
Inputs	4 inputs: Configurable for thermistor or dry contact. Inputs 1 and 2 are also configurable for 0–5 Vdc 10 bit A/D resolution. Binary input pulse frequency 10 pulses per second. Minimum pulse width (on or off time) required for each pulse is 50 msec
Outputs	1 analog output:0 to 10VDC (5mA maximum) with 8 bit D/A resolution using filtered PWM 3 binary outputs: Relay contacts rated at 1A max @ 24VAC/VDC, configured normally open.
Protection	Incoming power and network connections are protected by non-replaceable internal solid state polyswitches that reset themselves when the condition that causes a fault returns to normal. The power, network, input and output connections are also protected against voltage transient and surge events.
Battery	10-year lithium CR2032 battery provides a minimum of 10,000 hours of trend data retention during power outages.
Status Indicators	LED status indicators for BACnet MS/TP communication, run status, error, power and all digital outputs
Controller Addressing	Rotary DIP switches set BACnet MS/TP or ARCnet address of controller.
Listed by	UL-916 (PAZX), cUL-916 (PAZX7), FCC Part 15-Subpart B-Class A, CE EN50082-1997, UL94-5VA plenum rated enclosure
Environmental Operating Range	Operating: 32° to 130°F (0° to 54°C) 10 to 90% RH, non-condensing Storage: -24° to 140°F (-30° to 60°C) 10 to 90% RH, non-condensing
Power Requirements	24VAC +/- 10%, 50-60Hz, 14 VA power consumption, 26VDC (25V min, 30V max), single class 2 source only, 100 VA or less

更多 United Faith Sdn Bhd 相关资料