TM500 (Torque Monitor)

The TM500 is an indicator that can be easily connected to UTMⅡ/UTMV via the attached (supplied) cable.
By connecting UTMⅡ with the rotary encoder option, the relationship between torque and angle (or displacement/distance) change can be displayed in a graph (waveform), which in turn, is used for thorough waveform comparison.
There are two modes for waveform comparison useful for various purposes: “continuous” and “average” mode.
In “continuous mode,” HI and/or LO control outputs will be turned ON when the sensor input level goes over or below the high/low limit for predetermined number of times.
In “average mode,” a mean/average waveform data is calculated from a preset numbers of waveform data for OK/Not OK (NG) evaluation.

 

Features

■ Torque monitor for UTMⅡ/UTMV
■ Waveform display of torque variation against angles
■ Suitable for low-speed rotation and direct-acting applications
■ Hold function
■ Upper/lower limit of displacement against initial torque can be compared
■ Save measurement data and setting values in an SD card
■ Easy connection to UTMⅡ/UTMV with one cable
■ Operation power source can be supplied to the UTMⅡ/UTMV. (also to an optional rotary encoder)

Application example

＜Screw driver with torque monitoring＞

 

＜Physical sensory test＞

 

Specifications

Analog section｜Display section｜Setting section｜External I/O signal｜Interface｜General performance｜Attachments

Analog section
Torque input	-5 to +5V　Input impedance：1MΩ or more
Accuracy	Non-linearity : Within 0.02%FS±1digit Zero drift : Within 0.2mV/℃ RTI Gain drift : Within 0.01%/℃
Analog filter	Low pass filter (-6dB/oct.) Select from 30, 100, 300, 1kHz
A/D converter	･ Rate : 4000times/sec ･ Resolution : 24bit (binary)　　Approx. 1/30000 with respect to 5V
Monitor output	Output level : Input voltage cuff (For test point)
Pulse input (Open collector)	Maximum input frequency : 50kHz Internal counting range : Approx. 1000000

Display section
Display unit	3.5 inch TFT color LCD

Setting section
Setting method	Setting by analog type touch panel operation
Preservation of set values	NOV RAM (nonvolatile RAM), Lithium-battery-backed-up C-MOS RAM

External I/O signal
External output (15)	Hold result (Load, DPM)／Overload／Wave result／Complete／RUN／Load OK／DPM OK／SD OK
External input (12)	Load Digital Zero／DPM Positioning／Start／Stop／Hold／Reset／Backlight On／Prohibit Touch Panel／Work change

Interface
Interface	RS-232C

General performance
Power supply	DC24V(±15%)
Power consumption	7W typ.
Operating conditions	Temperature：Operation　-10 to +40℃　Storage　-20 to +60℃ Humidity：85%RH or less (non-condensing)
Dimensions	96(W)×96(H)×117.3(D)mm (Projections excluded)
Weight	Approx. 1.0kg
CE marking certification	EMC directives EN61326-1

Attachments
	Operation manual･･････1 External input/output connector･･････1 Cable for UTMⅡ/UTMV connection (2m)･･････1 Cable for UTMⅡrotary encoder connection (2m)･･････1 SD card (1GB)(with SDC option)･･････1

Product	Description
SDC	SD card slot (Approx. 80 waveforms can be preserved by 1MB, SDHC and SDXC are not supported.) All indicated values and all comparison waveforms can be saved and restored. Measured waveforms and judgment points can be saved automatically.

Product	Description
DTC1	Case for TM500 (with AC power supply)
SD1G	1GByte card
SD2G	2GByte card
CA81-232X	miniDIN-D-Sub9p cross cable 1.5m
CATM21-M	Cable for UTMⅡ/UTMV connection 2m
CATM51-M	Cable for UTMⅡ/UTMV connection 5m
CATM(R)21-M	Cable for UTMⅡrotary encoder connection 2m
CATM(R)51-M	Cable for UTMⅡrotary encoder connection 5m
CN52	FCN series I/O connector (with cover)
CN57	FCN series I/O connector (with diagonal cover)
CN60	Circular DIN 8p connector for RS-232C
CN90	Waterproof plastic connector for UTMⅡ/UTMV connection
CN91	Waterproof plastic connector for UTMⅡrotary encoder connection
GMP96x96	Rubber packing
TSU03	DC lighting surge unit

Download

Product catalogue(PDF)		TM500 catalogue(594 KB)