Features |
||||
 Color LCD touch screen allows intuitive operation. |
 B5 size ideal for measurements in the field. Light weight: only 1.2 kg including amplifier and battery. |
 Removable lithium-ion battery can be exchanged in the field. |
 IPX54 waterproof rating for main unit. |
 Support for wireless measurements eliminates need for cumbersome cabling on site. |
Screen images
RIONOTE intuitive user interface
Lets the user select the required program for the respective purpose:
SX-A1FT (FFT analysis), SX-A1RT (octave band analysis), or SX-A1WR (waveform recording). The right side of the screen provides access to various settings. |
|
 |
|
|
RIONOTE calibration screen
Serves for calibration of microphones or accelerometers connected to the RIONOTE.
|
|
 |
|
|
Waveform recording
By using the waveform recording program, it is possible to display and record the time waveform of the incoming signal(s). Available recording time depends on the number of input channels and the selected frequency range. The figure below shows a time waveform displayed on the screen of the Main Control Unit.
 |
|
RIONOTE System Configuration
Zoom in by clicking on the image.
|
FFT analysis program SX-A1FT
|
|
|
FFT analysis
RIONOTE enables you to perform FFT analysis on multiple channels simultaneously. The results are shown in clear graphs on the large color screen, in real time, or from stored data when using the recall function. A marker allows you to scroll through the data, and enables the readout of the level of a frequency of interest.
|
Transfer function
The transfer function represents the relation between an input signal and output signal in the frequency domain, allowing the determination of amplitude and phase.In this mathematical calculation category, the RIONOTE supports coherence function and cross spectrum processing.
|
 |
 |
|
Waveform post processing
After completing waveform recording (as explained above), the stored waveforms can be displayed on the Main Control Unit's large screen, and played back by using the earphone jack output. Moreover, various secondary post processing functions for the waveform data are available in the Main Control Unit, including FFT analysis as shown in the screen example below.
|
|
 |
|
1/3 octave band analysis program SX-A1RT
|
|
|
Octave band analysis
Real time analysis of noise or vibration levels for evaluation and designing countermeasures is usually performed by means of octave band analysis (using either octave bands or 1/3 octave bands). The below screen sample of the RIONOTE displays octave analysis results in 4 channels as a graph and numeric values at the same time.
|
|
 |
|
Vibration Analysis Program SX-A1VA
|
|
|
This program adds vibration measurement functions to the RIONOTE Multifunction Measurement System.
All essential vibration measurement functions are provided, enabling equipment diagnosis and trend management for industrial machinery.
The program also supports detailed diagnosis including FFT analysis and envelope processing.
|
|
 |
|
Judgement Program (Pass/Fail Evaluation) SX-A1CMP
|
|
|
It is suitable for pass / fail evaluation of noise, vibrations and other phenomena in production or inspection lines.
Allows setting threshold areas for FFT analysis results to determine pass/fail.
Depending on the evaluation purpose, a suitable sensor can be selected from various types of microphones or accelerometers.
Operation control from a PLC is also supported as an option (using the Ethernet connector of the RIONOTE).
|
|
 |
|
Order Tracking Program CAT-SAA1-ORDTRK
|
|
|
Output the analysis results by connecting microphone, accelerometer as well as tachometer.
Waveform recording enables reanalysis. |
|
 |
|
|
Optional Programs for the RIONOTE
Multifunction Measurement System
A wide range of optional programs are available to make measurement operations even more speedy and convenient.
|
|
|
*Details will be shown at the point of a mouse.
1
|
| Product name | Product number | |||
|---|---|---|---|---|
| RIONOTE 2 channel FFT Analyzer | SA-A1FTB2 | |||
| RIONOTE 4 channel FFT Analyzer | SA-A1FTB4 | |||
| RIONOTE 2 channel Octave Analyzer | SA-A1RTB2 | |||
| RIONOTE 4 channel Octave Analyzer | SA-A1RTB4 | |||
| RIONOTE 2 channel Frequency Analyzer (FFT and Octave) | SA-A1FTRTB2 | |||
| RIONOTE 4 channel Frequency Analyzer (FFT and Octave) | SA-A1FTRTB4 | |||
| RIONOTE Program for FFT Analysis | SX-A1FT | |||
| RIONOTE Program for 1/3 Octave Analysis | SX-A1RT | |||
| Judgement Program (Pass/Fail Evaluation) | SX-A1CMP | |||
| Vibration Analysis Program | SX-A1VA | |||
| Order Tracking Program | CAT-SAA1-ORDTRK | |||
| Product name | Product number | |||
|---|---|---|---|---|
| Wireless Dock | SA-A1WD | |||
| Lithium-ion Rechargeable Battery (spare) | SAA1S38 | |||
| 32 GB SD Card | MC-32SP3 | |||
| 2 GB SD Card | MC-20SD2 | |||
| Voice Memo Microphone | BSHSM03BK | |||
| Monitor Earphone | ATH-C320-BK | |||
| Shoulder Belt | VA-12015 | |||
| Carrying Case | SAA10660 | |||
| LCD Protector | 59SA5000 | |||
| RIONOTE Desktop Stand | SA-A1S36 | |||
| LCD Protector | - | |||
| CCLD 4 mA Modification (factory option) | - | |||
| Input section | ||||
|---|---|---|---|---|
| Number of channels | 4 (2), BNC connectors,CCLD, AC/DC | |||
| Max. input voltage | ±13 V | |||
| CCLD | 2 mA 24 V (4 mA Factory option) | |||
| Amplifier section | ||||
| Frequency Range | DC to 20 kHz or 0.25 Hz to 20 kHz | |||
| Input range | -40 dB to 20 dB, 20-dB steps, 0 dB ref.1 Vrms | |||
| Residual noise | At range full-scale: -85 dB or less (0 dB range, AP level) | |||
| Dynamic range | 100 dB or better (0 dB range, fs = 51.2 kHz, 400 line FFT noise level) | |||
|
Phase difference between channels |
±1 deg. or less (1 Hz to 20 kHz, same input range) | |||
| A/D converter section | ||||
| A/D converter | 24 bit, delta-sigma type, simultaneous sampling | |||
| Sampling frequencies | 51.2 kHz, 25.6 kHz, 12.8 kHz, 5.12 kHz, 2.56 kHz,1.28 kHz, 512 Hz, 256 Hz | |||
| Display | 10.1 inch TFT color LCD, 1 280 x 800 pixels, transmissive type | |||
| Touch panel | Multi-touch (2 points), projected capacitive type | |||
| Input/output section | ||||
| USB | USB A x 1, mini B x 1 | |||
| Earphone jack | Yes Stereo mini jack, φ3.5 | |||
| SD card slot | Yes (SDHC support, max. 32 GB) | |||
| Tacho pulse input, General purpose input | ||||
| Number of channels | 1, BNC connector | |||
| Tacho pulse | ||||
| Input voltage range |
0 - 12 V, open collector supported, internal pull-up 3.3 V (pull-up resistance 1 kΩ) |
|||
| H-L threshold level | 2.5 V | |||
| Measurement rotation speed range | 5 000 pulse/s | |||
| General purpose | ||||
| A/D converter | 10 bit successive approximation type | |||
| Sampling frequency | Approx. 10 Hz | |||
| External trigger | Open collector supported, internal pull-up 3.3 V | |||
| Power supply | Li-Ion battery (battery life approx. 4 hours, depending on usage conditions), AC adapter | |||
| Dimensions, Weight |
40 (H) x 275 (W) x 188 (D) mm SA-A1: 1 200 g (incl. 280 g battery, SA-A1B4 mounted) |
|||
| Water-resistant rating | Equivalent to IP54 | |||
| Operating temperature range | -10 °C to +50 °C using AC adapter, max. 90 % RH (no condensation) | |||
| Supplied accessories | Rechargeable Li-Ion battery x 1, AC adapter NE-20P x 1, SA-A1 file converter, AS-70 Viewer | |||
| Input | 4 or 2 channels (Amplifier SA-A1B4/B2 needed) | |||
|---|---|---|---|---|
|
Signal transfer to main platform |
LAN port | Ethernet 100 base-TX | ||
| Wireless | WLAN (IEEE802.11a/b/g/n, 2.4/5 GHz) | |||
| Distance of wireless transfer | about 50 m＊Depending on usage conditions | |||
| Memory | SD card (SDHC support, max 32 GB) | |||
| Power supply | 8 IEC R6 (sizeAA) batteries(alkaline or nickel-hydride), AC adapter | |||
| Dimensions, Weight | Approx. 42 (H) × 193 (W) × 95 (D) mm, Approx. 500 g (incl. battery) | |||
| Water-resistant rating | IP grade IP54 equivalent (same as main unit) | |||
| General real-time analysis processing | ||||
|---|---|---|---|---|
| Processing outline | FFT analysis (non-continuous frames when used in real time) | |||
| Number of channels | Max. 4 channels | |||
| Trigger | Trigger modes | Free, Single, Repeat | ||
| Trigger source | Waveform, External, Rotation speed | |||
| Trigger position | ±2/N(N: number of analysis points) | |||
| Arithmetic functions |
Time domain waveform for 1 frame, Power spectrum, Cross spectrum, Transfer function, Coherence |
|||
| Window functions | Rectangular, Hanning, Flat-top, Exponential, Force | |||
| Analysis frequencies | 20 kHz, 10 kHz, 5 kHz, 2 kHz, 1 kHz, 500 Hz, 200 Hz, 100 Hz | |||
| Number of analysis points | 256, 512, 1 024, 2 048, 4 096, 8 192, 16 384, 32 768 | |||
|
Averaging and other processing functions |
Linear, Exponential, Max Hold | |||
| Number of averaging runs | 1 to 1 024 | |||
| General post-analysis processing | ||||
| Outline | FFT analysis of WAVE files recorded with WR function | |||
| Number of channels | Max. 4 channels | |||
| Arithmetic functions |
Time waveform for 1 frame, Power spectrum, Cross spectrum, Transfer function, Coherence, Partial overall |
|||
| Window functions | Rectangular, Hanning, Flat-top, Exponential, Force | |||
| Number of analysis points | 1 024, 2 048, 4 096, 8 192, 16 384, 32 768 | |||
| Overlap ratio | 0 %, 25 %, 50 %, 75 % | |||
|
Averaging and other processing functions |
Linear, Exponential, Max Hold | |||
| Number of averaging runs | 1 to 1 024 | |||
| Standard compliance |
JIS C1513 class 1, JIS C1514 class1, IEC 61260:1995 class1, ANSI S1.11-2004 class1 |
|||
|---|---|---|---|---|
| Band filter center frequencies and number of bands | ||||
| Octave bands | 0.5 to 16 000 Hz, 16 bands Max. 4 channels | |||
| 1/3 octave bands | 0.4 to 20 000 Hz, 48 bands Max. 3 channels | |||
|
Instantaneous value data (every 100 ms) |
Time weighted level Lp, Time averaged level Leq, Time weighted maximum level Lmax |
|||
| Processing value data |
Time averaged level Leq, Sound exposure level LE, Time weighted maximum level Lmax, Time weighted minimum level Lmin, Time percentile level LN (5, 10, 50, 90, 95, 33.3), max. 5 values |
|||
| Store function | Auto/Manual | |||
|
Time weighting characteristics |
F (Fast) 125 ms, 630 ms, S (Slow) 1 s, 10 s | |||
|
Frequency weighting characteristics |
A, C, Z | |||
| Trigger | Trigger modes | Free, Single, Repeat | ||
| Trigger source | AP level, Band level, External signal, Time | |||
|
Number of recording channels |
1 to 4 channels + rotation or General purpose DC | |||
|---|---|---|---|---|
| Frequency range | 20 kHz, 10 kHz, 5 kHz, 1 kHz, 500 Hz, 100 Hz | |||
| Quantization | 16 bit/24 bit | |||
| Trigger | Trigger modes | Free, Single, Repeat | ||
| Trigger source | Waveform, Time, External, Rotation speed | |||
| Voice memo marker function | Yes | |||
| Monitor output (playback) | Allows listening to recorded data (51.2 kHz, 25.6 kHz, 12.8 kHz only) | |||
| Recorded data | WAVE format | |||
Malaysia
