| Nominal diameter | 1/2 ″ (15A) | |
| Material connection | Inlet | Rc1 / 2 |
| Discharge port | ||
| Air connection | Supply port | Rc1 / 4 (with air cock) |
| exhaust port | Rc3 / 8 (with muffler) * | |
| Service air pressure | 0.2 to 0.7 MPa | |
| Discharge pressure | 0.7MPa | |
| Discharge rate / cycle | 70mL | |
| Slurry limit (maximum passing particle diameter) | 1mm or less | |
| Mass |
-15BA NDP: 4.1Kg NDP-15BS □: 6.3Kg NDP-15FP □: 3.5Kg NDP-15FVT: 4.3Kg |
|
* The silencer is built into the pump body.
Rc3 / 8 screw holes are machined for connecting hoses to guide exhaust to ducts.
 |
Since the NDP-15 series uses the DP-10 series diaphragm, select the NDP-20 series that is one size up for large-scale operation at 20L / min or higher. NDP-15BA □ series uses nylon (PA) as the material for the valve receiver. Pay attention to corrosion resistance. Not suitable for MEK etc. |
| Body (wetted part) material | Diaphragm material | ||||
|
C: Chloroprene (CR) |
N: |
T: Fluorine resin (PTFE) |
H: |
S: Polyolefin-based thermoplastic elastomer (TPO) |
|
| A: Aluminum alloy (ADC12) |
NDP-15BAC (851946) |
NDP-15BAN (851947) |
NDP-15BAT (851945) |
NDP-15BAH (851948) |
NDP-15BAS (852680) |
| S: Stainless steel (SCS14) |
NDP-15BSC (851958) |
NDP-15BSN (851959) |
NDP-15BST (851957) |
NDP-15BSH (851960) |
NDP-15BSS (852681) |
|
P: Polypropylene (PPG) |
NDP-15FPC (851903) |
NDP-15FPN (851943) |
NDP-15FPT (851698) |
NDP-15FPH (851905) |
NDP-15FPS (852683) |
|
V: Polyolefin full oil (PVDF) |
--- | --- |
NDP-15FVT (852141) |
--- | --- |
Note) Clicking the model / product number will display the parts list and parts exploded view.
|
Model |
NDP-15BA □ |
NDP-15BS |
NDP-15FP |
NDP-15FVT |
|
Ball valve Flat valve |
NDP-15FP □ / NDP-15FVT ・ ・ ・ PTFE |
|||
|
Valve seat |
A5056 |
SUS316
|
PPG |
PVDF |
|
Valve holder |
PA |
|||
|
Center disc |
A5056 |
PPG (SUS304 *) |
PVDF (SUS304 *) |
|
* SUS304 is insert material
★ Valve model
NDP-15BA □ / NDP-BS □ ・ ・ ・ Ball valve
NDP-15FP □ / NDP-15FVT ・ ・ ・ Flat valve ★ The flat valve type cannot handle slurry.
★ The initial self-priming lift is 1m for all models.
|
|
The maximum operating pressure of the body wetted part resin type (FP □ / FVT) is It depends on the liquid temperature. Be sure to check the liquid temperature-maximum working pressure diagram. |
Malaysia
