Assembly Lube - Spanjaard Malaysia

The 3 Spanjaard Anti-Scuff Pastes in our range all contain a high percentage of MoS2. They are all used for the assembly of moving parts to prevent scuffing and scoring when running in and to provide initial lubrication before an elastohydrodynamic lubricating film can be formed. In addition, they are used for the pre-treatment of large open gears prior to conversion to Open Gear

Lubricant 1279.
The load-carrying capacity of MoS2 is in excess of 2750 Mpa (400 000 psi). No fluid lubricants are capable of withstanding such high loads. The different properties of the 3 Spanjaard Anti-Scuff Pastes are highlighted in the table below.

This product is manufactured in compliance with DTD 5617; NATO Code S722 and Joint Services Designation ZX-38

868
This product is specifically used in the assembly of jet turbines using synthetic oils. It is a feature of this product that the base will slowly evaporate above 250°C without oxidising, leaving behind the lubricating film. Approved as an anti-seize compound on nuts and threads/studs in the higher temperature zone of the ABB turbo chargers.

Typical Properties

TYPICAL PROPERTIES		SPANJAARD ANTI-SCUFF PASTE
		Standard Grade	845	868
Worked penetration 1/10mm		285	280	295
MoS2 particle size		0.7µ Av.
Drop point, °C		180	>200	210
Base		Petroleum		Synthetic
Thickener		Lithium		Lithium complex
APPLICATIONS
Complies with		-	Mil-M-7866
Lubricant for:	Phosphor-bronze bearings	Yes		No
	Assembly of engines & assembly of all moving parts for bedding-in without scuffing or scoring	Yes		Jet turbine/ turbo charger’s nuts & bolts
Pre-treatment of:	Plain bearings	Yes
	Gears	Yes
	Piston rings	Yes		Aircraft
	Cams	Yes
	Lathe centres	Yes		No
Anti-seize for:	Nuts and bolts	Yes		Aircraft
	Cocks	Yes
	Screw threads (refrigerants systems)	Yes
	Press fittings	Yes
	Turbine studs	Yes		Aircraft
Operating temperature range	Lower, °C	-20		-73
	Upper, °C	150	200	120
Contents of smallest pack		700g	500g

A gelled, soft paste assembly compound in aerosol form with a high Molybdenum Disulphide (MoS2) content used for engine or parts assembly to ensure bedding in without scuffing, pick-up or scoring. Also used as an anti-seize for pipe threads and for pre-treatment of large open gears. Anti-Scuff Paste can be used if a paste is preferred.

Spanjaard Anti-Scuff Spray is used for the assembly of moving parts. It reduces wear by providing lubrication during running-in. Also used for the pre-treatment of new or reconditioned plain bearings, gears, piston rings, cams, lathe centres and slides and their controls.

Prevents seizure in nuts and bolts, valves and cocks, screw threads (drill pipe tool joint lubricant, threads in refrigeration systems), press fittings and turbine studs.

A lubricant for phosphor bronze bearings - particularly in generating equipment, bulk head mechanisms, cylinder plungers and turbine relay valves. Used on loaded equipment linkages subject to high impact stresses or twisting.

Assembling machines with Spanjaard Anti-Scuff Spray results in the elimination of scuffing, pick-up or scoring during the bedding-in period, after which time the machine will run for its full designed life with minimum wear.

Even when the oil components begin to oxidise at above 200°C the MoS2 provides solid film lubrication up to 450°C.

The load carrying capacity of MoS2 is in excess of 2 750 Mpa (400 000 psi), above the yield point of most metals, and cold forming of the metal under the MoS2 film can take place without “welding” or pick-up occurring. Thus, when a hydro-dynamic oil film wedge is not present, wear or damage is prevented.