F650-CK is a weighing indicator designed for in-motion check weigher.
With high-performance filter to attenuate noise and vibration, stable and accurate weight measurement can be achieved.
All necessary functions for check weighers like over/under evaluation, ranking or sorting, various weighing modes, conveyor controls, statistics, and so on are packed into this model.
| Analog section | |
| Excitation voltage | DC5V±5％ Output current：within 90mA Ratiometric method（Up to 6 load cells at 350Ω can be connected in parallel.） |
|---|---|
| Signal input range | －0.3 to 3.0 mV/V |
| Zero adjustment range | －0.2 to 3.0 mV/V Automatic adjustment by digital computation |
| Gain adjustment range | Automatic adjustment by digital computation |
| Accuracy |
Non-linearity：within 0.01％/FS±1digit（when 3mV/V is input） Zero drift：0.025μV/℃ RTI Typ Gain drift：1ppm/℃ Typ |
| A/D converter | Conversion rate : 1000 times/sec Resolution : 24bit (binary) |
| Theoretical calibration | Equivalent input calibration : accuracy when theoretical calibration is performed : 1/1,000 |
| Filter | |
| Digital filter | Moving average (common for all modes) : OFF, 2 to 999 times |
|---|---|
| Low-pass filter | Variable : 2.0 to 10.0Hz |
| Display section | |
| Display unit | TFT color LCD module 3.5inch (320×240dot) Display area : 71(W) x 53(H) mm ×53(H)mm |
|---|---|
| Weight display | 5-digits (signs: minus sign on the highest numerical digit) |
| Unit | NONE, kg, t, g, N, or lb (selectable) |
| Decimal place | 0, 0.0, 0.00, or 0.000 (selectable) |
| Status display | BUSY, GO, EMP, SMP, COMP, NZ, STAB |
| Setting section | |
| Setting method | Setting by analog touch panel operation (with a key click buzzer)Setting can be performed by external devices as well via RS-232C interface and so on. |
|---|---|
| Setting value memory | Initial values F.RAM (nonvolatile RAM), other values : lithium-battery-backed-up C-MOS RAM |
| Settings protection | Setting operation can be prohibited to prevent changes by miss-operation (LOCK 1, LOCK 2, LOCK 3). |
| Setting item |
・Standard mode (COMP MODE SEL.: COMP): CODE/STANDARD/OVER/UNDER/UPPER/LOWER ・Standard mode (COMP MODE SEL.: RANK.1): CODE/BOUNDARY 0/BOUNDARY 1/BOUNDARY 2/BOUNDARY 3/UPPER/LOWER ・Standard mode (COMP MODE SEL.: RANK.2): CODE/BOUNDARY 0/BOUNDARY 1/BOUNDARY 2/BOUNDARY 3/BOUNDARY 4/ BOUNDARY 5/BOUNDARY 6/BOUNDARY 7/BOUNDARY 8/BOUNDARY 9/UPPER/LOWER ・Checker mode: CODE/TAKING MODE/TRIGGER MODE/TAKING COUNT/TAKING RATIO/EMPTY COUNT/NEAR ZERO/DIGITAL LPF /MOV. AVE. FILTER/GROSS RATIO/HISTOGRAM TARGET/HISTOGRAM RANGE ・State output: CODE/OUTPUT SEL. 0/OUTPUT SEL. 1※/OUTPUT SEL. 2※/OUTPUT SEL. 3※/OUTPUT SEL. 4※ ※Selectable from OUTPUT, COMP, NZ, TAKING, ERROR, LOWER, STAB, RUN ・Graph: CODE/GRAPHIC MODE/TRIGGER LEVEL/X END POINT/Y START POINT/Y END POINT/DRAWING WEIGHT/ PRE TRIG.VALUE/FRONT OF FILTER ・Result: CODE/AVE.WEIGHT/MAX.WEIGHT/MIN.WEIGHT/CNT.OF DATA/GEN.STAN.DEV./SMP.STAN.DEV./MAX. - MIN./LATEST DATA ・Comparison: COMP MODE SEL./STAND. CMP SEL./COMPLETE OUT T./NEAR ZERO COMP./HI/LO COMP. SEL./PRESET TARE WGT.1 /PRESET TARE WGT.2/HOLD SELECT ・Operation: MD (PERIOD)/MD (RANGE)/ZT (PERIOD)/ZT (RANGE)/INDICATE COLOR/BACKLIGHT LOW TM/BACKLIGHT ON TM/ AUTO ACCUMULAT./OUTPUT MODE/OUTPUT COMP. MODE/WGT CODE INPUT/ZT MODE/AUTO ZERO AVE./B4 FUNK. SELECT/TAKING SPEED ・Communication: COMM. MODE/BAUD RATE/LENGTH/PARITY BIT/STOP BIT/TERMINATOR/FLOW CONTROL/ SI/F OUT1 SELECT/SI/F OUT2 SELECT ・System: INITIALIZATION/LOCK1/LOCK2/LOCK3/PASSWORD/LANGUAGE/[GROSS/NET] KEY/[DZ] KEY/[TARE ON] KEY/ SELF CHECK DSP1/SELFCHECK DSP2/SELFCHECK MEM/SELF CHECK KEY/SELF CHECK EXT/SELF CHECK COM ・Calibration: ZERO CAL./SPAN CAL./EQUIV. CAL./BALANCE WEIGHT/MIN. SCALE DIV./NET OVER/GROSS OVER/UNIT DISPLAY/ DECIMAL PLACE/DZ REGULATION VAL. |
| Total function | |
| Histogram display | Numbers of data for each 9 weight ranges are displayed. Two set of data out of the range are displayed as well. |
|---|---|
| Weighing results | Results are displayed for each code. |
| Statistics | Display statistics data stored on F650-CK. Display average weight, maximum weight, minimum weight, number of data, population standard deviation, sample standard deviation, difference between maximum and minimum, latest data. |
| External | |
| External output（10） | OVER or RANK1 or RANK20/GO or RANK2 or RANK21/UNDER or RANK3 or RANK22/ NONE or RANK4 or RANK23/NONE or RANK5 or STROBE/OUTPUT SEL. 0/OUTPUT SEL. 1/ OUTPUT SEL. 2/OUTPUT SEL. 3/OUTPUT SEL. 4 |
|---|---|
| External input（10） | CODE0/CODE1/CODE2 or KEY LOCK/Graph drawing/D/Z ON/TARE ON/TARE OFF/Accumulation command/Measurement start/Measurement reset |
| Interface | |
| SIF | 2-wire serial interface |
|---|---|
| 232 | RS-232C communication interface |
| 485 | RS-485 communication interface （Modbus-RTU /UNI-format）(option) |
| BCO | BCD parallel data output interface (Sink type)(option) |
| BSC | BCD parallel data output interface (Source type)(option) |
| DAV | D/A converter(voltage output) (option) |
| DAI | D/A converter(current output) (option) |
| ODN | DeviceNet interface (option) |
| CCL | CC-Link interface (option) |
| Only one option can be installed. | |
| General performance | |
| Operating voltage・Power consumption | 100 to 240 Vac ±10 to 15% (50/60Hz) 18W max |
|---|---|
| Operating conditions |
Operation temperature range: －10 to 40℃ Storage temperature range: －20 to ＋60℃ Humidity: 80%RH or less (non-condensing) |
| Dimension ・Weight | 96（W）×96（H）×138（D）mm（Projections excluded） approx.1.0kg |
| Attachments | |
| AC power cable (voltage resistance: 125 Vac ) (3m) ×1 | |
| Jumper cable ×2 | |
| FCN series I/O connector (with cover) ×1 | |
| Operation manual ×1 | |
| BCD output connector (when BCO option is installed) ×1 | |
| Mini screwdriver (when D/A converter option is installed) ×1 | |
| DeviceNet connector (with ODN option is installed) ×1 | |
| CC-Link connector (when CCL option is installed) ×1 |
| Optional accessories | |
| CA372-I/O | cable with FCN connector at one-end 3m |
|---|---|
| CA600-BCDCNV | FCN connector 32p-57・36p cabtyre cable 0.3m |
| CA81-232X | miniDIN-D-Sub9p cross cable 1.5m |
| CAAC2P-B3 | AC power cable 3m |
| CAAC3P-CEE7/7-B2 | AC power cable (voltage resistance: 250 Vac) 2m |
| CN50 | FCN series I/O connector (with cover) |
| CN51 | BCD output connector |
| CN55 | FCN series I/O connector (with diagonal cover) |
| CN60 | circular DIN 8p connector for RS-232C |
| CN71 | CC-Link connector |
| CN80 | analog I/O connector terminal |
| CND01 | DeviceNet connector |
| DTC2-PSL | case for F650 |
| GMP96×96 | rubber seal |
