AMILAN™ Nylon Resin About heat-resistant nylon resins CM1026 and CM3006 - General properties

AMILAN™ Nylon Resin About heat-resistant nylon resins CM1026 and CM3006 - General properties

Characteristics of heat-resistant grades CM1026 and CM3006

CM1026 is the heat-resistant grade of nylon 6, and CM3006 is the heat-resistant grade of nylon 66. Nylons are heat-resistant resins, having one of the highest melting points among thermoplastic resins. Toray's newly developed heat-resistant grades CM1026 and CM3006 possess the superb heat resistance of nylon and exhibit minimal thermal degradation under very humid conditions. Additionally, Toray offers CM3006E as a heat-resistant grade of nylon 66 designed for applications that require excellent electrical properties at high temperatures.

Mechanical properties

Table 1 compares the mechanical properties of CM1026 and CM3006 to general injection-molding nylons CM1021 and CM3001N. There is virtually no difference in mechanical properties compared to the general grades. Figures 1, 2, 3, 4 and 5 show changes in the general properties (tensile yield strength, flexural modulus and Izod-impact strength) of CM1026 and CM3006 as a function of temperature.

Table 1: General properties of CM1026, CM3006, and CM3006E
Property Unit Test method
(ASTM)
CM1021 CM1026
In a dry state Atmospheric
equilibrium
water absorption
3.5%
In a dry state Atmospheric
equilibrium
water absorption
3.5%
Tensile-yield strength kg/cm2 D638 740 310 775 340
Tensile-yield elongation % D638        
Tensile-breaking strength kg/cm2 D638        
Tensile-breaking elongation % D638 200 250 150 200
Flexural-yield strength kg/cm2 D790        
Flexural modulus kg/cm2 D790 24,000 5,300 25,000 6,000
1% compressive-distortion stress kg/cm2 D659 255 55 260 60
Compressive-yield strength kg/cm2 D659 840 - 870 -
Shear strength kg/cm2 D732 590 430 600 435
Rockwell hardness R scale D785 114 85 115 86
Izod-impact strength 23°C kg·cm/cm D256 6 >50 5 50
(1/2”) -30°C kg·cm/cm D256 4 10 4 10
Linear expansion coefficient /°C D696 8×10-5 - 7×10-5 -
Heat distortion temperature (18.56kg/cm2) °C D648 65 - 67 -
Heat distortion temperature (4.64kg/cm2) °C   150 - 155 -
Melting point °C   215 - 215 -
Specific gravity -   1.13 - 1.14 -
Water absorption
2 hours at 100°C
% D570 4.4 - 4.3 -
Water absorption
24 hours at 23°C
%   1.9 - 1.8 -
Burning characteristics   UL
D635
94V-2
Self-extinguishing
94V-2
Self-extinguishing
Property Unit Test method
(ASTM)
CM3001N CM3006
CM3006E
In a dry state Atmospheric
equilibrium
water absorption
2.5%
In a dry state Atmospheric
equilibrium
water absorption
2.5%
Tensile-yield strength kg/cm2 D638 800 530 810 550
Tensile-yield elongation % D638        
Tensile-breaking strength kg/cm2 D638        
Tensile-breaking elongation % D638 110 200 80 200
Flexural-yield strength kg/cm2 D790        
Flexural modulus kg/cm2 D790 28,000 12,000 28,000 12,000
1% compressive-distorton stress kg/cm2 D659 280 90 285 95
Compressive-yield strength kg/cm2 D659 910 - 910 -
Shear strength kg/cm2 D732 675 600 680 600
Rockwell hardness R scale D785 118 100 118 101
Izod-impact strength 23°C kg· cm/cm D256 4 14 4 14
(1/2”) -30°C kg·cm/cm D256 2 7 2 7
Linear expansion coefficient /°C D696 10×10-5 - 9×10-5 -
Heat distortion temperature (18.56kg/cm2) °C D648 75 - 77 -
Heat distortion temperature (4.64kg/cm2) °C   180 - 180 -
Melting point °C   255 - 255 -
Specific gravity -   1.14 - 1.14 -
Water absorption
2 hours at 100°C
% D570 3.9 - 3.8 -
Water absorption
24 hours at 23°C
%   1.5 - 1.4 -
Burning characteristics   UL
D635
94V-2
Self-extinguishing
94V-2
Self-extinguishing
  • Figure 1: Change in yield strength as a function of temperature (nylon 6)Figure 1: Change in yield strength as a function of temperature (nylon 6)
  • Figure 2: Change in yield strength as a function of temperature (nylon 66)Figure 2: Change in yield strength as a function of temperature (nylon 66)
  • Figure 3: Change in flexural modulus as a function of temperature (nylon 6)Figure 3: Change in flexural modulus as a function of temperature (nylon 6)
  • Figure 4: Change in flexural modulus as a function of temperature (nylon 66)Figure 4: Change in flexural modulus as a function of temperature (nylon 66)
  • Figure 5: Change in impact strength as a function of temperature

    Figure 5: Change in impact strength as a function of temperature

Resistance to thermal degradation

Ⅰ. Continuous thermal resistance

Not only nylons but all plastic materials exhibit degradation of physical properties when exposed to heat and oxygen in high-temperature atmospheres. The degree of degradation increases with higher temperatures or longer durations of exposure. The stress-strain curve from a tensile test most clearly expresses this degradation of properties.
Figure 6 shows an example model for nylon 66. When exposed to high temperatures, at first elongation at breakdown declines gradually (the yield point does not change significantly). Finally, the yield point terminates (brittle fracture failure) and stress and elongation decrease.

Figure 6: Change in the stress-strain curve resulting from thermal degradation

Figure 6: Change in the stress-strain curve resulting from thermal degradation

We can conclude that the change in elongation allows us to determine the extent of degradation. Figures 7, 8 and 9 show the change in elongation, tensile strength and impact strength in CM1021 and CM1026 resulting from exposure to high temperatures. Figures 10, 11 and 12 show the change in elongation, tensile strength and impact strength in CM3001N and CM3006 resulting from exposure to high temperatures. Clearly you can see higher temperatures and longer durations lead to greater declines in elongation and tensile strength.

  • Figure 7: Thermal degradation test (Tensile strength)

    Figure 7: Thermal degradation test (Tensile strength)

  • Figure 8: Thermal degradation test (Tensile-breaking elongation)

    Figure 8: Thermal degradation test
    (Tensile-breaking elongation)

  • Figure 9: Thermal degradation test (Izod-impact strength)

    Figure 9: Thermal degradation test (Izod-impact strength)

  • Figure 10: Thermal degradation test (Change in tensile strength)

    Figure 10: Thermal degradation test
    (Change in tensile strength)

  • Figure 11: Thermal degradation test (Change in tensile-breaking elongation)

    Figure 11: Thermal degradation test
    (Change in tensile-breaking elongation)

  • Figure 12: Thermal degradation test (Change in Izod impact strength)

    Figure 12: Thermal degradation test
    (Change in Izod impact strength)

Based on this data, Figure 13 plots the temperature and time where elongation and tensile strength have decreased 50%.

Figure 13: Thermal resistance (Half-life of tensile properties)

Figure 13: Thermal resistance (Half-life of tensile properties)

This is referred to as an Arrhenius plot, which facilitates estimating the relationship between temperature and lifetime. The same expressed in a formula would look like this:

Figure 13 shows a stark difference between CM1026 and CM3006 on the one hand and CM1021 and CM3001N on the other.
Table 2 shows the impact strength results from a tensile-impact strength test. Figures 14, 15 and 16 compare these results with a foreign competitor’s heat-resistant grade product.

  • Figure 14: Thermal degradation properties (tensile strength, 180°C)Figure 14: Thermal degradation properties
    (tensile strength, 180°C)
  • Figure 15: Thermal degradation properties (tensile impact, 150°C)Figure 15: Thermal degradation properties
    (tensile impact, 150°C)
  • Figure 16: Thermal degradation properties (tensile impact, 120°C)

    Figure 16: Thermal degradation properties
    (tensile impact, 120°C)

Table 2: Thermal degradation properties (Tensile-impact strength)
Conditions Tensile- impact strength(kg·cm/cm2)
CM3006 CM3006(Black) Foreign competitor A’s
Heat-resistant grade
Before treatment 331 318 257
180°C 2 days
   5 days
   10 days
567
420
116
560
400
113
485
412
125
150°C 2 days
   5 days
   10 days
545
330
221
455
320
215
401
388
226
120°C 2 days
   5 days
   10 days
456
460
449
391
427
444
359
321
402

(Notes)
1) Test: ASTM D1822 1/8"t L type
2) Measured at 23°C, RH65%
3) 150°C and 120°C tests still underway.

Ⅱ. Heat cycling properties

Nylon is used frequently in environments where temperatures fluctuate from high to low and low to high. For example, nylon used in engine compartment components is exposed to a repetitive cycling of temperatures as high as 120°C (when the engine is running) to as cold as -30°C to -40°C (when left outside in the bitter cold). To anticipate how a material will perform under such a severe environment, heat cycle tests are performed. The test specimen is left in 120°C air for one hour, then immediately exposed to a -40°C environment. The results of these heat cycle tests are shown in Table 3.
Even after 70 cycles, both CM1026 and CM3006 retained at least 90% of their tensile-breaking strength. CM1026 retained 80% of its elongation and CM3006 retained 60%. CM1026 and CM3006 both retained at least 80% of their Izod-impact strength.

Table 3: Heat cycling properties
  Unit CM1026 CM3006
Before treatment
Tensile-breaking strength
Elongation
Izod-impact strength

kg/cm2
%
kg·cm/cm

727
231
4.9

818
97
4.1
10 cycles
Tensile-breaking strength
Elongation
Izod-impact strength

kg/cm2
%
kg·cm/cm

718
185
4.7

888
90
3.9
10 cycles
Tensile-breaking strength
Elongation
Izod-impact strength

kg/cm2
%
kg·cm/cm

739
189
4.4

822
72
3.6
10 cycles
Tensile-breaking strength
Elongation
Izod-impact strength

kg/cm2
%
kg·cm/cm

748
178
4.3

809
63
3.6
10 cycles
Tensile-breaking strength
Elongation
Izod-impact strength

kg/cm2
%
kg·cm/cm

692
182
4.3

783
58
3.7
10 cycles
Tensile-breaking strength
Elongation
Izod-impact strength

kg/cm2
%
kg·cm/cm

679
163
4.0

742
55
3.5

(Notes)
1) Conditions 120°C 1hr- -40°C 1hr
2) Test specimen: ASTM D638 Type I (3-mm thickness), n = 10
3) Measurement conditions: 23°C RH65%

Ⅲ. Electrical properties

Demand is growing for heat-resistant nylon in materials and components used in electronics equipment. In these applications, the relationship between electrical properties and temperature, as well as any change in electrical properties when exposed to high temperatures for extended periods of time, are important factors to consider.
Compared to standard nylons, CM1026 and CM3006 experience little change in electrical properties when exposed to high temperatures.
Figures show the change in volume resistivity and dielectric tangent when exposed to 150°C or 120°C for extended durations of time, compared to standard nylon grades.

Figure 17-1 Figure 17-2

Figure 17


Figure 18-1 Figure 18-2 Figure 18-3

Figure 18


Figure 19-1 Figure 19-2

Figure 19


Figure 20-1 Figure 20-2

Figure 20


Figure 21

Figure 21


Figure 22-1 Figure 22-2

Figure 22

Ⅳ. Resistance to oil

In recent years, more and more automotive components are taking advantage of nylon’s superior resistance to oil. CM1026 and CM3006 are the ideal materials to use in high-temperature environments such as automotive engine compartments, where components come in direct contact with gasoline, brake oil or gear oil. Examples of some applications include fuel strainers, oil reserve tanks, canisters, fuel pipes and more.
Table 4 shows the change in properties of CM3006 when immersed in regular or high-octane, commercially available gasoline for three months at room temperature to demonstrate resistance to gasoline. Izod-impact strength and Rockwell hardness remained mostly unchanged, tensile-yield strength declined only slightly and elongation grew. This could be attributable to toluene or other aromatic hydrocarbons contained in the gasoline.

Table 4-1: CM3006 gasoline resistance: Regular gasoline (Nippon Oil Silver)
Immersion
duration
(months)
Tensile-breaking strength
kg/cm2
Elongation
(%)
Izod-impact strength
kg·cm/cm
Rockwell hardness
R scale
0
1
2
3
895
831
849
849
95
85
125
150
4.5
4.3
4.5
4.7
121
122
122
122
Table 4-2: CM3006 gasoline resistance: Regular gasoline (Nippon Oil Gold)
Immersion
duration
(months)
Tensile-breaking strength
kg/cm2
Elongation
(%)
Izod-impact strength
kg·cm/cm
Rockwell hardness
R scale
0
1
2
3
895
828
827
827
95
75
160
140
4.5
4.6
4.9
4.7
121
122
121
121

(Notes)
1) Plans call for the immersion test to continue for two years at room temperature
2) Test conditions: 23°C RH65%
Tensile: ASTM D638 n = 5
Impact: ASTM D256 n = 10
Hardness: ASTM D785 n = 10

Table 5 shows the results of changes in weight and properties after 300 or 600 hours immersed in 120°C synthetic gasoline (isooctane/toluene = 70/30Vol%). These results are illustrated in Figures 23-26.

Table 5: Resistance to hot gasoline
Material and category Treatment time(hrs)
0 302 600
CM3006
Weight change %
Tensile-yield strength kg/cm2
Tensile-breaking strength
Elongation %
Tensile-impact strength kg·cm/cm2

-
814
622
98
317

+0.56
828
612
53
377

+0.87
676
514
66
370
CM3006 (Black)
Weight change %
Tensile-yield strength kg/cm2
Tensile-breaking strength
Elongation %
Tensile-impact strength kg·cm/cm2

-
805
666
99
311

+0.58
815
587
61
398

+0.93
661
481
67
380
Foreign competitor A’s heat-resistant grade BLACK
Weight change %
Tensile-yield strength kg/cm2
Tensile-breaking strength
Elongation %
Tensile-impact strength kg·cm/cm2

-
808
588
37
327

+0.49
815
617
41
397

+0.77
675
518
38
375

(Notes)
1) Gasoline: isooctane/toluene = 70/30(vol%)
2) Temperature: 120±5°C
3) Test
Tensile: ASTM D638 Type13mm n = 5
Tensile impact: ASTM D1822 1/16" L TYPE n = 10

Figure 23 Resistance to hot gasoline (Weight increase (%))

Figure 23
Resistance to hot gasoline
(Weight increase (%))

Gasoline: isooctane/toluene = 70/30 (vol%)
Temperature: ±5°C
Sample: Tensile test specimen (ASTM D638 Type1 3 mm)


Figure 24: Resistance to hot gasoline (Tensile-yield strength)

Figure 24:
Resistance to hot gasoline
(Tensile-yield strength)

Gasoline: isooctane/toluene = 70/30 (vol%)
Temperature: 120±5°C
Sample: ASTM D638 Type1 3mm

○CM3006
●CM3006 (Black)
× Foreign competitor A’s heat-resistant grade


Figure 25 Resistance to hot gasoline (Elongation)

Figure 25
Resistance to hot gasoline
(Elongation)

Gasoline: isooctane/toluene = 70/30 (vol%)
Temperature: 120±5°C
Sample: ASTM D638 Type1 3mm

○CM3006
●CM3006 (Black)
× Foreign competitor A’s heat-resistant grade


Figure 26: Resistance to hot gasoline (Tensile-impact strength)

Figure 26:
Resistance to hot gasoline
(Tensile-impact strength)

Gasoline: isooctane/toluene = 70/30 (vol%)
Temperature: 120±5°C
Sample: ASTM D1822 1/16" L TYPE

○CM3006
●CM3006 (Black)
× Foreign competitor A’s heat-resistant grade

Next, to investigate the effects of exposure to gear oil, our nylon products were immersed in 80°C or 100°C gear oil continuously for 90 days. The measurement results of tensile properties and impact strength are shown in Figures 28 and 29. No property changed significantly, confirming that our nylons are largely unaffected by the test conditions.
As shown in Figures 30 and 31, exposure to brake fluid leads to greater elongation and impact strength and reduced tensile-yield strength.

  • Figure 27: Resistance to gear oil (Elongation)Figure 27: Resistance to gear oil (Elongation)
  • Figure 28: Resistance to gear oil (tensile-breaking strength, impact strength) Figure 28: Resistance to gear oil
    (tensile-breaking strength, impact strength)
  • Figure 29: Resistance to brake fluid (elongation)Figure 29: Resistance to brake fluid (elongation)
  • Figure 30: Resistance to brake fluid (elongation)Figure 30: Resistance to brake fluid (elongation)